background image

2

E-flite F-4 Phantom 32 DF Assembly Manual

Notice

All instructions, warranties and other collateral 

documents are subject to change at the sole 

discretion of Horizon Hobby, Inc. For up-to-date 

product literature, visit http://www.horizonhobby.
com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product 

literature to indicate various levels of potential harm 

when operating this product:

NOTICE

: Procedures, which if not properly followed, 

create a possibility of physical property damage  

AND a little or no possibility of injury.

CAUTION

: Procedures, which if not properly followed, 

create the probability of physical property damage 

AND a possibility of serious injury.

WARNING

: Procedures, which if not properly followed, 

create the probability of property damage, collateral 

damage, and serious injury OR create a high 

probability of superficial injury. 

This is a sophisticated hobby product and NOT a 

toy. It must be operated with caution and common 

sense and requires some basic mechanical 

ability. Failure to operate this Product in a safe 

and responsible manner could result in injury or 

damage to the product or other property. This 

product is not intended for use by children without 

direct adult supervision. Do not attempt disassembly, 

use with incompatible components or augment 

product in any way without the approval of Horizon 

Hobby, Inc. This manual contains instructions for 

safety, operation and maintenance. It is essential to 

read and follow all the instructions and warnings 
in the manual, prior to assembly, setup or use, in 

order to operate correctly and avoid damage or 

serious injury.

 Warnings

Read and follow all instructions and safety precautions 
before use. Improper use can result in fire, serious 
injury and damage to property.

Age Recommendation:  

For advanced fliers ages 14 and above.  

This is not a toy.

COMPONENTS

Use only with compatible components. Should any 
compatibility questions exist, please refer to the 
product instructions, the component instructions or 
contact Horizon Hobby, Inc.

FLIGHT

Fly only in open areas to ensure safety. It is 
recommended flying be done at AMA (Academy of 
Model Aeronautics) approved flying sites. Consult local 
laws and ordinances before choosing a location to fly 
your aircraft.

INTAKE/FAN

Keep loose items that can get entangled in the 
fan away from the intake and exhaust, including 
loose clothing or other objects such as pencils and 
screwdrivers. Especially keep your hands away from 
the intake and exhaust, as injury can occur.

BATTERIES

Notes on Lithium Polymer Batteries

When misused, lithium polymer batteries are 
significantly more volatile than alkaline or Ni-Cd/
Ni-MH batteries used in RC applications. Always 
follow the manufacturer’s instructions when using and 
disposing of any batteries. Mishandling of Li-Po batteries 
can result in fire causing serious injury and damage.

SMALL PARTS

This kit includes small parts and should not be left 
unattended near children as choking and serious injury 
could result.

SAFETY PRECAUTIONS

•   Check all control surfaces prior to each takeoff.
•   Do not fly your model near spectators, parking 

areas or any other area that could result in injury to 
people or damage of property.

•   Do not fly during adverse weather conditions. 

Poor visibility and/or strong winds can cause 
disorientation and loss of control of your aircraft.

•   Do not take chances. If at any time during flight you 

observe any erratic or abnormal operation, land 
immediately and do not resume flight until the cause 
of the problem has been ascertained and corrected. 
Safety can never be taken lightly.

•  Do not fly near power lines.

 

WARNING

: Read the ENTIRE instruction 

manual to become familiar with the features of the 

product before operating. Failure to operate the 

product correctly can result in damage to the 

product, personal property and cause serious injury.

Содержание F-4 Phantom 32 DF















































Отзывы: