manualshive.com logo in svg

E-FLITE F-4 Phantom 32 DF, Инструкция по сборке

Поделиться
Скачать
E-FLITE F-4 Phantom 32 DF Скачать руководство пользователя страница 29

28

E-flite F-4 Phantom 32 DF Assembly Manual

  9. Cut a notch at the front of the cover to fit over the 

fan mounting lugs.

  10. Fit the cover to the fan, trimming as necessary 

to fit the cover tightly over the fan and exhaust tube. 
Use flexible tape to secure the cover to the fan and 
exhaust tube. Make sure to tape over any areas that 
would allow air to pass between the airflow of the 
propulsion system and the inside of the fuselage.

Nose Gear Installation

Required Parts

Fuselage assembly  Transmitter
Receiver 

Receiver battery

Silicone tubing 

Metal clevis (2)

2mm nut (2) 

Threaded rod, 2mm x 40mm

Servo with hardware
3mm x 8mm socket head screw (4)
Aluminum wheel collar with setscrew, 3.5mm
Aluminum wheel spacer, 3.5mm
Wheel, 1

5

/

16

-inch (33mm)

Dual wheel axle adapter set

Required Parts (Fixed Gear Specific)

Fixed nose gear assembly

Required Parts (Retract Specific)

Nose gear retract assembly
Nose gear strut

Required Tools and Adhesives

Side cutter 

Hobby knife with #11 blade

Clear tape 

Threadlock

Pin vise 

Drill bit: 1/16-inch (1.5mm)

Pencil 

Hex wrench: 1.5mm, 2.5mm

Flat file 

Phillips screwdriver: #1

The installation of the retracts and fixed 

gear follow the same procedure. The only 
difference is the installation of the nose gear 
strut, which has been highlighted in gray.

  1. Use a #1 Phillips screwdriver to remove the four 

2mm x 8mm self-tapping screws that secure the 
nose gear cover to the fuselage. Set the cover and 
screws aside until later in the section of the manual.

  2. Place the grommets and brass eyelets into the 

servo mounting tabs. Note the positioning of the 
brass eyelets, as the servo will be mounted to the 
top of the plate in the fuselage.

Содержание F-4 Phantom 32 DF















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды