background image

40

E-flite F-4 Phantom 32 DF Assembly Manual

LIMITATION OF LIABILITY

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 
INDIRECT, INCIDENTAL OR CONSEQUENTIAL 
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR 
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF 
WHETHER SUCH CLAIM IS BASED IN CONTRACT, 
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY 
OR ANY OTHER THEORY OF LIABILITY, EVEN IF 
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY 
OF SUCH DAMAGES. Further, in no event shall the 
liability of Horizon exceed the individual price of the 
Product on which liability is asserted. As Horizon 
has no control over use, setup, final assembly, 
modification or misuse, no liability shall be assumed 
nor accepted for any resulting damage or injury. By 
the act of use, setup or assembly, the user accepts all 
resulting liability. If you as the purchaser or user are 
not prepared to accept the liability associated with the 
use of the Product, purchaser is advised to return the 
Product immediately in new and unused condition to 
the place of purchase.

LAW

These terms are governed by Illinois law (without 
regard to conflict of law principals).  This warranty 
gives you specific legal rights, and you may also have 
other rights which vary from state to state.  Horizon 
reserves the right to change or modify this warranty at 
any time without notice.

Warranty Services

QUESTIONS, ASSISTANCE, AND SERVICES

Your local hobby store and/or place of purchase 
cannot provide warranty support or service. Once 
assembly, setup or use of the Product has been started, 
you must contact Horizon directly. This will enable 
Horizon to better answer your questions and service 
you in the event that you may need any assistance. 
For questions or assistance, please direct your 
email to [email protected], or call 
877.504.0233 toll free to speak to a Product Support 
representative. You may also find information on our 
website at www.horizonhobby.com.

INSPECTION OR SERVICES

If this Product needs to be inspected or serviced, please 
use the Horizon Online Service Request submission 
process found on our website or call Horizon to obtain a 
Return Merchandise Authorization (RMA) number. Pack 
the Product securely using a shipping carton. Please 
note that original boxes may be included, but are not 
designed to withstand the rigors of shipping without 
additional protection. Ship via a carrier that provides 
tracking and insurance for lost or damaged parcels, 
as Horizon is not responsible for merchandise until it 
arrives and is accepted at our facility. An Online Service 
Request is available at http://www.horizonhobby.
com under the Support tab. If you do not have internet 
access, please contact Horizon Product Support to obtain 
a RMA number along with instructions for submitting 
your product for service. When calling Horizon, you will 
be asked to provide your complete name, street address, 
email address and phone number where you can be 
reached during business hours. When sending product 
into Horizon, please include your RMA number, a list of 
the included items, and a brief summary of the problem.  
A copy of your original sales receipt must be included 
for warranty consideration. Be sure your name, address, 
and RMA number are clearly written on the outside of 
the shipping carton.

Notice: Do not ship LiPo batteries to Horizon. If you 

have any issue with a LiPo battery, please contact 

the appropriate Horizon Product Support office.

WARRANTY REQUIREMENTS 

For Warranty consideration, you must include your 
original sales receipt verifying the proof-of-purchase 
date. 

Provided warranty conditions have been met, 

your Product will be serviced or replaced free of 
charge. Service or replacement decisions are at the 
sole discretion of Horizon.

NON-WARRANTY SERVICE

Should your service not be covered by warranty 
service will be completed and payment will be 
required without notification or estimate of the 
expense unless the expense exceeds 50% of the 
retail purchase cost. 

By submitting the item for service 

you are agreeing to payment of the service without 
notification. Service estimates are available upon 
request. You must include this request with your item 
submitted for service. Non-warranty service estimates 
will be billed a minimum of ½ hour of labor. In 
addition you will be billed for return freight. Horizon 
accepts money orders and cashiers checks, as well as 
Visa, MasterCard, American Express, and Discover 
cards. By submitting any item to Horizon for service, 
you are agreeing to Horizon’s Terms and Conditions 
found on our website http://www.horizonhobby.com/
Service/Request/.

UNITED STATES

(Electronics and engines)

Horizon Service Center

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Online Repair Request visit:

www.horizonhobby.com/service

(All other products)

Horizon Product Support

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Содержание F-4 Phantom 32 DF















































Отзывы: