background image

E-flite Diamante 5e ARF Assembly Manual

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide 

warranty support or repair. Once assembly, setup or use of the 

Product has been started, you must contact Horizon directly. 

This will enable Horizon to better answer your questions and 

service you in the event that you may need any assistance. 

For questions or assistance, please direct your email to 

[email protected], or call 877.504.0233 toll 

free to speak to a service technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for 

a Return Merchandise Authorization (RMA). Pack the Product 

securely using a shipping carton. Please note that original boxes 

may be included, but are not designed to withstand the rigors 

of shipping without additional protection. Ship via a carrier that 

provides tracking and insurance for lost or damaged parcels, as 

Horizon is not responsible for merchandise until it arrives and 

is accepted at our facility

. A Service Repair Request is available 

at www.horizonhobby.com on the “Support” tab. If you do not 

have internet access, please include a letter with your complete 

name, street address, email address and phone number where 

you can be reached during business days, your RMA number, 

a list of the included items, method of payment for any non-

warranty expenses and a brief summary of the problem. 

Your original sales receipt must also be included for warranty 

consideration. Be sure your name, address, and RMA number 

are clearly written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original 

sales receipt

 verifying the proof-of-purchase date. Provided 

warranty conditions have been met, your Product will be 

repaired or replaced free of charge. Repair or replacement 

decisions are at the sole discretion of Horizon Hobby.

Non-Warranty Repairs

Should your repair not be covered by warranty the repair 

will be completed and payment will be required without 

notification or estimate of the expense unless the expense 

exceeds 50% of the retail purchase cost.

 By submitting the item 

for repair you are agreeing to payment of the repair without 

notification. Repair estimates are available upon request. You 

must include this request with your repair. Non-warranty repair 

estimates will be billed a minimum of ½ hour of labor. In 

addition you will be billed for return freight. Please advise us 

of your preferred method of payment. Horizon accepts money 

orders and cashiers checks, as well as Visa, MasterCard, 

American Express, and Discover cards. If you choose to pay 

by credit card, please include your credit card number and 

expiration date. Any repair left unpaid or unclaimed after 90 

days will be considered abandoned and will be disposed of 

accordingly. 

Please note: non-warranty repair is only available 

on electronics and model engines.

Electronics and engines requiring inspection or repair should be 

shipped to the following address:

Horizon Service Center 

4105 Fieldstone Road 

Champaign, Illinois 61822

All other Products requiring warranty inspection or repair should 

be shipped to the following address:

Horizon Product Support 

4105 Fieldstone Road 

Champaign, Illinois 61822

Please call 8-50-0 with any questions or concerns 

regarding this product or warranty.

Содержание Diamante 25e ARF









































Отзывы: