manualshive.com logo in svg

E-FLITE Blade CP Pro 2 PNP, Руководство пользователя

Поделиться
Скачать
E-FLITE Blade CP Pro 2 PNP Скачать руководство пользователя страница 12

22

23

With the stick pushed right, the swashplate will tilt to the right .

NOTE: 

HP6DSM Transmitter is shown for reference only .

Mode 2

Mode 1

If at any time during the test the swashplate controls do not respond properly, double-check the swashplate mixing 
settings in the transmitter . The values should be set as listed in the transmitter setup section of this manual . If 
the swashplate controls still do not respond properly after ensuring that the swashplate mixing values are correct, 
double-check the servo reversing settings in the transmitter .

If the controls still do not respond properly after ensuring the servo reversing settings are correct, you may also 
check the servo connections to the receiver . The connection for each servo should be connected to the receiver 
as listed in the Receiver Connection and Installation section of this manual .

Once you have confirmed proper swashplate mixing values, servo reversing settings and servo connection 
locations, all controls should be functioning properly . However, if you continue to encounter any problems relating 
to your Blade CP Pro 2 PNP responding properly to the transmitter, do not fly . Call the Horizon Support Team at 
1-877-504-0233 before proceeding .

If you have confirmed proper control operation of your Blade CP Pro 2 PNP, continue with servo arm and  
linkage adjustment .

Содержание Blade CP Pro 2 PNP





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды