Dynatron 900+, Руководство оператора

Страница: 13 / 32

Dynatron 900
+™
9
DETAILED TREATMENT SETUP
1. According to manufactures’ instructions, prepare the patient for treatment. Make sure all belts
and harnesses are securely attached.
2. The Remote Stop cable must be plugged into the console before the device is turned “on.”
Connect the Remote Stop plug to the Remote Jack located in the center of the rear panel and
hand the Remote Stop switch to the patient.
3. Turn the Power Switch to “1” (on). The On/Off Toggle switch is located on the lower
left-side of the control panel. When the toggle switch is in the “1” (on) position, the LED above
the Reset Key is illuminated green. The digital display windows are also illuminated green
indicating that there is power to the device.
4. Set Treatment Time: (1-99 min.) Using the up/down arrow keys located immediately under
the Time Display Window, set the treatment time. The treatment time will appear in the Time
Display Window and the display will count down during a treatment. Treatment time ranges
from 1-99 minutes and may be adjusted in 1 minute intervals.
Note: Traction forces may be changed during treatment; however the Start Key must be pressed
after each change. Changes made during the treatment, will not take effect until the next new
Hold/Rest cycle begins.
4. Set Hold Force Time (1-99 sec.). Located directly above the “Hold Force” knob, Hold Time
is selected by pressing the up/down arrow keys below the Hold Display. This selection
determines the amount of time the traction tension will hold after reaching the set Hold Force.
Hold Force Time ranges from 1 - 99 seconds and may be adjusted in 1 second intervals. When
a Static traction treatment is desired, set the Hold Time at “- -”.
5. Set Rest Force Time (1-99 sec.). Located directly above the “Rest Force” knob, Rest Time is
selected by pressing the up/down arrow keys below the Rest Display. This timer determines the
amount of time the Rest tension will hold after reaching the preset Rest Force. Rest Force Time
ranges from 0 - 99 seconds and may be adjusted in 1 second intervals. When a static traction
treatment is desired, set the Hold Time at “- -”. The Rest Force setting is ignored.
6. Set Hold Force (
4 – 200 lbs.; 2 – 91 kg; or 20 – 890N).
Hold Force is set by using the
circular knob located on the right-hand side of the control panel. Three numbered circles
surround the knob, the inside circle indicates force in Netwons, the middle circle in kilograms,
while the outside circle indicates force in pounds. Force is selected by aligning the gray dot on
top of the knob with the desired/ pounds/kilograms of force indicated on the circles. Hold force
ranges from
4 – 200 lbs.; 2 – 91 kg; or 20 – 890N.
7. Set Rest Force (
0 – 197 lb.; 0 – 90 kg; 0 – 890N).
Rest force is set by using the circular knob
located on the left-hand side of the control panel. Three numbered circles surround the knob,
the inside circle indicates force in Netwons, the middle circle in kilograms, while the outside
circle indicates force in pounds. Rest Force is selected by aligning the gray dot on top of the
knob with the desired/ pounds/kilograms of force indicated on the circles. Rest force ranges
from
0 – 197 lb.; 0 – 90 kg; 0 – 890N.
9. Adjust Speed ( 8 lbs.-17 lbs. per second). Adjust the variable "Pull" and "Release" speed of the
rope by using the Speed knob located on the left side of the control panel. The rope speed is
increased by turning the knob to the right and reduced by turning the knob to the left. Rope
Speed can be adjusted between slow and fast (8 lbs. -17 lbs. per second).
10. Press Start. Press Start and the treatment begins. If a beeper sounds when Start is pressed at
the beginning of a treatment, be sure that the “Rest” Force is set lower than the “Hold” Force.
Press the Reset Key to reset the alarm and indicator lamps.