Dynapac D.ONE Скачать руководство пользователя страница 66

Страница: 66 / 190

5.5 Checking the hydraulic oil level

NOTICE!
Components may get damaged!

–

Check the hydraulic oil level at room tempera-

ture (approx. 20 °C (68 °F)).

–

If, during the daily inspection of the oil level the

hydraulic oil level is found to have dropped,

check all lines, hoses and components for

leaks.

–

Use only oil of the permitted specification

Chapter 8.3.5 „Hydraulic oil“ on page 108

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Check the oil level in the inspection glass.

Normal level

Approx. 3 cm (1.2 in) below the top

edge of the inspection glass

Minimum level

Approx. middle of inspection glass

If necessary, check the lines, hoses and units for leaks.

In the event of an internal leakage in the

hydraulic system, hydraulic oil might collect

in the travel drive or exciter shaft housing.

If necessary, check the travel drive or exciter shaft housing

Chapter 10 „Troubleshooting“ on page 149

For topping up, clean the area around the filling port.

Remove the cap and fill with hydraulic oil.

Close the cap.

B-SYM-1071

Fig. 49

Hydraulic Oil

B-720-0061

Fig. 50

Checks prior to start up – Checking the hydraulic oil level

D.ONE

Содержание D.ONE































































































































































































Результаты поиска

Содержание D.ONE

Отзывы:

Похожие инструкции для D.ONE

Бренды по названию

Популярные бренды

Dynapac D.ONE, Руководство по эксплуатации

Результаты поиска

Содержание D.ONE

Отзывы:

Похожие инструкции для D.ONE

Бренды по названию

Популярные бренды