background image

NOTE: Even with the air supply removed the marker may 
have gas inside. Be sure to vent this gas.  Make sure there are 
no paintballs in the breech and dry fire the marker in a safe 
direction.

NT11 BOARD

SETTINGS AND FUNCTIONS

TURNING THE NT11 ON AND OFF

To turn on the NT11, press and hold the power button for 
3 seconds (see figure 1) until the LED’s turn blue. The blue 
light indicates board boot up. After the boot up sequence, 
the LED’s will turn either RED (no ball) or GREEN (ball 
ready to fire). To turn the NT11 off, press and hold the power 
button until the LED’s turn off.

NOTE: THE NT11 AUTOMATICALLY SWITCHES OFF AFTER 
10 MINUTES OF NON-USE.

FIRING THE NT11

As soon as the marker is turned on and the LED’s turn from 
blue to either red or green, the NT11 is ready to fire. If there 
is no ball and the LED’s are RED, you need to hold the 
trigger for 1 second to force the NT11 to fire once. If there is 
a paintball inside the breech and the LED is green, just press 
the trigger to fire the marker.

LED LIGHT INDICATOR

The NT11 uses two super bright LED’s mounted on the circuit 
board inside the grip frame. These two lights are used to 
provide information to the user about the NT11. They will 
always show the same information and it does not matter 
which LED you look at. One is mounted behind the DYE 
logo on the left side of the grip panels. The other one can be 
seen by looking at the top left side of the grip frame while 
holding the NT11 in the position you would while playing a 
game.

FIGURE 1

NOTE: The eye is always activated 
when you turn the marker on.

W W W . D Y E P A I N T B A L L . C O M

W W W . D Y E P A I N T B A L L . C O M

6

7

ULTRALITE AIRPORT - FEEDNECK

  

CAM LEVER FEED NECK

The Cam Lever Feedneck is adjustable to fit any standard 
loader. To adjust the cam locking system, lift the cam lever 
away from the feed collar, and rotate the lever clockwise 
to tighten or counterclockwise to loosen the grip on 
the loader. Once the cam lever is facing in the forward 
direction, press the cam lever down against the feed collar 
to secure the loader in the feedneck. To loosen the locking 
system and remove the loader, lift the cam lever away 
from the feed collar. Take care not to over-tighten the cam 
locking system. The lever should not be overly difficult to 
lower into the locked position.

ON/OFF ULTRALITE AIRPORT

The NT11 comes equipped with an ON/OFF Ultralite Airport 
attached to the bottom of the frame. To turn on the gas 
supply, rotate the side lever counter clockwise until the 
internal stop is reached. To turn off the gas supply, rotate 
the side lever clockwise until the other stop is reached. As 
you rotate the side lever past the mid point, the residual gas 
between the Hyper3™ and the ON/OFF airport will vent. See 
page 32 for service information.  To remove the UL Airport 
from the UL frame see page 26.

Содержание NT11























Отзывы: