AIR LEAKING FROM BACK OF THE NT11
If the leak is coming from around the bolt back cap:
• Check that the bolt kit is tightened all the way into
the NT11. If the bolt kit is loose, it will start to leak.
• Remove the bolt kit and change the
020 O-ring
on the rear cap. Lube well and re-insert the bolt
kit into the NT11. Check bolt kit detail on page
19 for O-ring locations.
If the leak is coming from the bleed button:
• Make sure the gun is not out of air.
• Service the
005 O-rings
on the bleed button.
• Check
011 O-ring
on rear of spacer rod.
• See pages 13-19 for details.
AIR LEAKING FROM FRONT OF THE NT11
Determine if air is leaking from inside of bolt or
around bolt. Put your finger in breech and press
against bolt face to feel if air pressure builds up
behind your finger.
• If leak is coming from inside of bolt check the
014
O-ring
on plunger, and the front
010 O-ring
on the
spool.
• If the leak is coming from around the bolt check the
front
020 O-ring
and
017 O-Ring
on the cylinder.
• See page 13-19 for details.
LOW EFFICIENCY
•
Inspect the rear
020 O-Ring
on the cylinder.
• Inspect the bolt sail
015 O-Ring
on the bolt.
• Inspect the
012 O-ring
on the plunger.
• See page 13-21 for details.
NT11 DOES NOT CYCLE
•
The
012 O-ring
on the plunger may be damaged.
• The spool may be installed backwards.
• Front
010 O-ring
may be damaged.
• The dwell may be set too low.
NT11 DOUBLE FIRES
•
Rear
020 O-ring
on cylinder may be damaged.
• The
014 O-ring
on plunger may be damaged.
• The spool spring may need replacing
• The front bumper on the spool may need replacing
• The dwell may be set too high.
PROBLEMS WITH ELECTRONICS
NT11 WON’T TURN ON
•
Make sure battery is new and well charged.
• Make sure battery is inserted in the correct polarity.
• Make sure there is no dirt or debris blocking the
button from being pressed.
• Make sure the buttons are able to activate the
switches on the board.
NT11 WILL TURN ON / OFF BY ITSELF OR
THE EYES WILL TURN ON / OFF
BY THEMSELVES
• Both of these problems are caused because the
button(s) are being held in the down position.
• Remove the button cover and clean the area.
See page 34 for service details.
TROUBLESHOOTING GUIDE
W W W . D Y E P A I N T B A L L . C O M
W W W . D Y E P A I N T B A L L . C O M
36
37
TROUBLESHOOTING GUIDE
MARKER SHOOTING SLOW WHEN EYE IS ON
AND BLINKING GREEN
•
The eyes are not working correctly. Clean the eyes.
You’ll know that they are clean if the LED turns red
when there is nothing inside the breech of the NT11.
• Make sure the eye wires are not broken or pinched.
• The battery may be low. In this case, the battery
should be changed as soon as possible.
• If nothing above helps contact a store or DYE
Precision for eye replacement.
SOLENOID WILL NOT ACTIVATE / TRIGGER
NOT WORKING
• Check that the trigger adjustment is not set so that
the microswitch cannot activate. You should hear a
small click when pulling the trigger.
• If the NT11 fires once when turned on but not after
that, your trigger is set so that the microswitch is
always activated. Re-adjust the trigger.
• Change the battery if not positive about it’s charge.
• Check that the solenoid cable is attached to the
board and to the correct connector (solenoid
should be attached to the two prong connector).
TRIGGER BOUNCE / NT11 SHOOTING
MORE THAN ONE BALL PER PULL IN SEMI-
AUTOMATIC MODE
• Raise the trigger sensitivity level in the
configuration mode.
• Check that the trigger is not adjusted too short.
• Make sure there is a trigger spring inside the frame.
ERRATIC VELOCITY / WON’T FIRE
NT11 FIRES BUT BALLS ARE DROPPING OFF
OR NOT EVEN COMING OUT OF THE BARREL
•
Make sure the battery is good.
• Raise the dwell to factory level (6).
• Make sure bolt is well lubed and moves well.
If there is too much friction in the bolt it will cause
the NT11 to shoot down. Replace O-rings causing
this excess friction.
• Make sure air system is screwed in all the way.
FIRST SHOT IS TOO HIGH
•
Change the seat inside the Hyper3™ Regulator
• See page 22 for service Details.
VELOCITY IS NOT CONSISTENT
• Make sure the paintballs you are using fit the barrel
good and are consistent in size. The stock barrel
with the NT11 is .688 size. You should be able to
blow the paintball through the barrel but they
should not roll through the barrel on their own.
• Remove the bolt kit and re-lube it. Change any
O-rings causing a lot of friction. Make sure 014
O-ring in bolt tip is in place and in good condition.
• Raise the dwell.
• Change the battery.
• Check that the Hyper3™ regulator is working
correctly and that the pressure is consistent.
A separate regulator testing tool is available for this.
If needed, dis-assemble and change worn out
O-rings and the regulator seat in the Hyper3™
regulator.
Содержание NT11
Страница 1: ... ...
