DURKOPP ADLER 887 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 50

background image

5

EN

1

General

These service instructions describe the adjustments that can be made
to the class

887

special sewing machine.

CAUTION!

The operations described in these service instructions may only be
carried out by qualified staff or other appropriately trained persons!

Caution: Risk of injury!

Turn the main switch off for repair, conversion and maintenance work
and separate the machine from the pneumatic supply line.

Any adjustment work and functional testing with the machine running
should be conducted only under observance of all safety measures
and with the greatest possible caution.

These service instructions describe the adjustment of the sewing
machine in a logical order. Please observe that various setting
positions are dependent on each other. Thus it is essential that the
settings be conducted while keeping to the order described.

For all adjustments of parts involved in the stitch formation, a new
undamaged needle must be inserted.

This text does not specifically mention any machine covers or panels
which must be removed or re-mounted in order to conduct inspections
or adjustments.

Note

Some shafts on the special

887

machine are provided with flat

eccentric surfaces. This significantly simplifies machine adjustments.

For all adjustments on flat surfaces, the first screw screwed in the
direction of the eccentric surface.

1.1

Setting gauges

The retention pin required for adjusting the machine in included with all
units. It is located with the machine accessories and can be attached
so that it is easily accessible below the oil tray.

«
...
5
6
7
8
9
...
»

Содержание 887 Series



















































Отзывы:

Нет отзывов

Похожие инструкции для 887 Series

Бренд: Samsung Страницы: 48

Бренд: Janome Страницы: 47

BOS-18 II 56382453

Бренд: Clarke Страницы: 28

Бренд: VeriFone Страницы: 40

Highlight MERCHANDISER 1RHCC30

Бренд: Zero Zone Страницы: 53

Бренд: Titan Страницы: 33

Бренд: Duerkopp Adler Страницы: 80

Бренд: GBC Страницы: 12

Citymaster 2000

Бренд: HAKO Страницы: 186

Бренд: Singer Страницы: 20

Minoltafax 1400

Бренд: Konica Minolta Страницы: 157

VISION:mini VCC-G21X31ACL

Бренд: CIS Страницы: 20

Union Special 36200L220-60

Бренд: JUKI Страницы: 56

aerobic twisting stepper

Бренд: Brookstone Страницы: 14

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 19

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды