background image

2

Bottom feed

2.1

Basic setting for stitch adjustment and stitch length limit

Rule:

1. When setting the stitch length at “

0

”, the stitch regulator gear should

have as little play (clearance) as possible when you press down on
the bartacking lever.

2. The maximum stitch length limit depends on the material to be sewn

and the sewing equipment being used (see operating instructions).

Loosen screw (1) and take off the settings dial (2).

Turn the screw (3) as far as needed to the right using a 10 mm
open-ended wrench. Verify that the stitch regulator gear is without
motion by pressing down on the bartacking lever. This fulfils rule 1.

Set the scaling ring (4) with stitch length “

0

” to align with the

circular mark (5).

Limit the stitch length according to rule 2. For this, screw the
retention pin (6) into the proper hole. The holes are marked with
numbers which indicate the maximum stitch length.

If a maximum stitch length of 7 mm is required, unscrew the
screw (6) for 2.5 mm. Another end stop is available for this length.

Put the settings dial (2) back on and tighten the screw (1).

Caution: Risk of injury!

Turn the main switch off.

Only carry out this basic stitch adjustment when the machine
is turned off.

ATTENTION: Danger of breakage!

If the set stitch length is larger than allowed by the sewing equipment
in use, then the needle will hit against the throat plate insert.

8

5

3

6

4

1

2

Содержание 887 Series



















































Отзывы: