DURKOPP ADLER 887 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 50

background image

8.2

Terminals to PCB connections - pneumatic variant

Description of DA199_2 (9850 838000) switchboard

X11 - 37-pole connector (to control box)
X12 - thread tensioner valve
X13 - secondary thread tensioner valve
X14 - bartacking valve
X15 - sewing foot valve
X16 - keypad
X17 - bobbin thread monitor
X18 - light barrier
X19 - 1. +24V

2. FA (thread trimming)
3. FF3 (functional outlet 3, e. g. puller, pneumatic material edge trimmer)
4. STL (stitch length valve)
5. +24V
6. FF2 (functional outlet 2)
7. NK (needle cooling)
8. FK (thread clamp)
9. /DB3000 (needle switch off)
10. 0V

FW/STL(FA) – auxiliary outlet (thread wiper/zero stitch length at thread trimming)
X20 - external outlet controlled with auxiliary pushbutton on keypad (Imax=50mA)
X21 - connection of auxiliary cable for bottom distribution (FA, +24V, GND)
X22 - external blocking of operation (e. g. thread lever guard switch, etc.)
X23 - connection of a side DAC switchboard (direct drive)
X24 - material edge trimmer microswitch
X25 - material edge trimmer mini motor
S1

- tilt sensor

S2

- sewing machine operation blocking mode; switch in ON position means that the sensor is without function

SENS. S1 = tilt sensor on switchboard; EXT.SENS. = sensor in connector X22
DAC SENS. = sensor on DAC side switchboard (direct drive)

47

EN

«
...
47
48
49
50
»

Содержание 887 Series



















































Отзывы:

Нет отзывов

Похожие инструкции для 887 Series

Бренд: Sagem Страницы: 48

Бренд: Baby Lock Страницы: 120

Бренд: Singer Страницы: 24

Бренд: Kärcher Страницы: 300

Бренд: Ayra Страницы: 13

Бренд: Riccar Страницы: 22

Бренд: Ultratec Страницы: 7

Galaxy Pro 2700-WX-HR

Бренд: Edic Страницы: 24

Бренд: Baby Lock Страницы: 42

KING COBRA 1200 PRO

Бренд: U.S. Products Страницы: 12

Бренд: Singer Страницы: 67

Бренд: Rosco Страницы: 50

Бренд: Muratec Страницы: 41

KENMORE 385. 1254180

Бренд: Kenmore Страницы: 56

Sewing machine cabinet 272.98100.490

Бренд: Kenmore Страницы: 13

SEARS 385. 17622

Бренд: Kenmore Страницы: 52

Kenmore 385.19106

Бренд: Kenmore Страницы: 71

Бренд: Kenmore Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды