Duratrax MAXIMUM MT Скачать руководство пользователя страница 19

Страница: 19 / 20

ENGINE TROUBLE SHOOTING

The engine starts

Does the engine

turn over easily?

Does it run

continuously?

Is fuel getting to

the engine?

Check for clogging in

the carburetor or fuel

line. Press the

primer pump and

check for fuel

spraying out of the

fuel line. If so,

replace the fuel line.

Is fuel in the

fuel line?

Is the glow plug

red hot?

Check the high speed needle

setting and prime the engine.

Is foreign matter

clogging the fuel

tank or fuel line?

Is the battery for

the glow plug
clip charged?

It should be

ready to go.

Is the high

speed needle

setting 1 to

1-1/2 turns out

from closed (if

the engine is

broken-in?)

Try starting the

engine again.

YES

Does the engine

quit when the

glow plug clip is

removed?

YES

Clear the engine

of fuel.

Reset the high

speed needle.

YES

Replace the

glow plug.

Check that the

pressure line is

connected to the

muffler. The fuel

may be bad.

The engine does not start

Does the engine

turn over easily

with the glow

plug removed?

The engine may

be flooded.

Clear the engine

of fuel.

YES

Check that

nothing is

caught in the

engine. Check

that the the

pull starter

operates

smoothly.

Press the

primer pump

and check for

fuel spraying

out of the fuel
line through a

small hole. If

so, replace

the fuel line.

YES

Remove the

obstruction from

the fuel tank or

fuel line.

Charge or

replace the

batteries.

YES

Replace the

glow plug.

Try starting the

engine again.

Содержание MAXIMUM MT





















Результаты поиска

Содержание MAXIMUM MT

Отзывы:

Похожие инструкции для MAXIMUM MT

Бренды по названию

Популярные бренды

Duratrax MAXIMUM MT, Руководство по сборке и эксплуатации

Результаты поиска

Содержание MAXIMUM MT

Отзывы:

Похожие инструкции для MAXIMUM MT

Бренды по названию

Популярные бренды