manualshive.com logo in svg

DuraTech Industries Haybuster 572, Инструкция по эксплуатации и справочник по запасным частям, Страница: 8 / 160

Поделиться
Скачать
DuraTech Industries Haybuster 572 Скачать руководство пользователя страница 8

iv

5 7 2   R O U N D   B A L E R    

 

O P E R A T I N G   I N S T R U C T I O N S

T A B L E   O F   C O N T E N T S

Section 4:  Baler Adjustment ..................................................... 24

4.1  Bale Density Gauge ....................................................................................... 24
4.2  Adjusting Bale Density .................................................................................. 24
4.3  Adjusting twine tension ................................................................................. 25
4.4  Adjusting gauge wheels ................................................................................. 25
4.5  Gate Locking Procedure ............................................................................... 26
4.6  Adjusting Compression Rack ....................................................................... 26
4.7  Adjusting Main Drive Chain Tension .......................................................... 27
4.8  Adjusting pickup drive chain ....................................................................... 27
4.9  Adjusting belt tracking ................................................................................. 28

4.10  Adjusting pickup float

 ................................................................................. 28

4.11  Material Trap Cleanout and Inspection .................................................... 29
4.13  Belt and Lacing Pin Inspection .................................................................. 29
4.12  Secondary Drive Chain Adjustment .......................................................... 29
4.14  Belt Installation and Routing ..................................................................... 30
4.15  Twine Pincher Adjustment ......................................................................... 31

Section 5:  Monitor ..................................................................... 32

5.1  Monitor Operation ........................................................................................ 32

 

5.1.1  Bale Monitor Screen ....................................................................... 32

 

5.1.2  General Layout of controller ........................................................... 32

5.2  Calibration of the 572 Baler – General ....................................................... 33
5.3 Other Diagnosis .............................................................................................. 35
5.4   Menu Screen ................................................................................................. 36

 

5.4.1 Misc. Setup Screen ........................................................................... 36

 

5.4.2  Twine setup values .......................................................................... 36

 

5.4.3  Net wrap setup values ..................................................................... 36

 

5.4.4  Misc Setup Screen ........................................................................... 37

 

5.4.5  % Full Definition

 ............................................................................. 37

 

5.4.6  Auto Start Delay definition

 .............................................................. 37

 

5.4.7  Start Wrap/Wrap Reset Functions ................................................... 37

 

5.4.8  Twine Dispensing Indicators ........................................................... 38

 

5.4.9  Twine Arms Position Indicator ........................................................ 38

 

5.4.10  Auto Dump Feature ....................................................................... 38

 

5.4.11  Faults Screen ................................................................................. 38

 

5.4.12  Bale History .................................................................................. 38

 

5.4.13  Baling sequence ............................................................................ 39

 

5.4.14  Tying Sequence ............................................................................. 39

Section 6:  Lubrication ............................................................... 40

6.1  Lubrication .................................................................................................... 40
6.2  Chain Oiler  .................................................................................................... 47

Содержание Haybuster 572

































































































































































Отзывы:

Нет отзывов