manualshive.com logo in svg

DuraTech Industries Haybuster 572, Инструкция по эксплуатации и справочник по запасным частям, Страница: 44 / 160

Поделиться
Скачать
DuraTech Industries Haybuster 572 Скачать руководство пользователя страница 44

34

5 7 2   R O U N D   B A L E R  

 

O P E R A T I N G   I N S T R U C T I O N S

3. BALE SHAPE CALIBRATION

1.  With the tractor running and the hydraulic lever locked in detent allowing oil flow through the valve body, 

the tailgate fully closed and the chamber empty.

2.  Engage PTO and run baler for a brief period and then disengage PTO.

3.  Check fault screen. If there is a square box by the 

BALE SHAPE FAULT

, check electrical connection 

before proceeding further. If there is a square box by 

BALE SHAPE NO CAL

, follow steps 4-7. If there 

is no square box by 

BALE SHAPE NO CAL

 skip to section 4.3 to test the calibration.

4.  From the monitor screen, press ESC button to go to the main menu. Press button #3 to go to misc. setup.

5.  From the misc. setup screen press button #3 

BALE SHAPE CAL

 and hold for 3 seconds.

6.  Check fault screen, if no square boxes appear the bale shape calibration is complete.

4. CALIBRATION TEST

1.  TWINE ARM TEST

 

• 

With the tractor running and the hydraulic valve locked in detent allowing oil flow through the    

 

valve body, select manual from the monitor screen, button #4, if not already selected. 

 

• 

Using the right arrow button extend the twine arms completely and check to see that they come    

 

together and meet in the middle of the baler.

 

• 

Using the left arrow button bring the twine arms home, check that the twine arms return to the    

 

home position completely and that the twine pinch blocks are closed completely. If the    

 

 

twine arms do not return to the home position completely they need to be calibrated  

 

 

 

again, refer to section 1.1.  If the pinch blocks are not completely closed adjustment of    

 

 

the connecting linkage needs to be performed.

2.  BALE SIZE TEST

 

• 

With the tractor running and the hydraulic lever locked in detent allowing oil flow through the    

 

valve body, press button on the orange box opening the tailgate. 

 

• 

As the belt tension arm starts to move up wards the bale size number on the monitor will increase   

 

as soon as the arm starts to move.

 

• 

If the arm moves and the bale size readout stays at zero, unplug the bale size sensor. (The sensor    

 

is located on the right hand side of the tension arm.) Turn tractor off and repeat bale size    

 

 

calibration in section 2.

3.  BALE SHAPE TEST

 

• 

With the tractor running and the hydraulic lever locked in detent allowing oil flow through the    

 

valve body, press button on the orange box opening the tailgate fully. Both bale shape bars should  

 

be increasing simultaneously as the bale size increases to its maximum value. 

 

• 

Start to close the tailgate; the belt tension arm will lower placing tension on belts. As this   

 

 

happens, the bale shape bars on the monitor should be the same height.

 

• 

If the bars are uneven, unplug the bale shape sensors. (The sensors are located on the left hand    

 

and right hand top of the tailgate.) Turn tractor off and repeat bale shape calibration in section 3.

Содержание Haybuster 572

































































































































































Отзывы:

Нет отзывов