Dunster House E9-3042DBPP-45 Скачать руководство пользователя | Manualshive

Страница: 18 / 26

background image

All dimensions are approximate and subject to the limitations of the material used and the methods of manufacture

Page 18

3x

N.1960 (cut to suit)

Trims above the door

IMPORTANT - Trims on the inside of the wall will create a support for
the roof boards.

IMPORTANT - Use a step ladder to install all the trims. Do not put your
weight on the roof before all roof boards are secured.

Cut to size N.1960 trim, to fit on the both sides of the door-overhanging

part of the top wall log, as shown on the diagram

Cut to size N.1960 trim, to fit on the both sides of the door-overhanging

part of the front wall, as shown on the diagram

Pre drill holes
To secure trims use 35mm screws

Cut to size N.1960 trim and fix it on top of the J.1960 trim

from the previous step

35mm screws

35mm screws

35mm screw

35mm screw

Top wall log

Front wall

N.1960 (cut to suit)

N.1960 (cut to suit)

N.1960 (cut to suit)

«
...
16
17
18
19
20
...
»

Содержание E9-3042DBPP-45



























Отзывы:

Нет отзывов

Похожие инструкции для E9-3042DBPP-45

Бренд: WoodLife Garden Страницы: 67

Бренд: finnhaus Страницы: 68

Carport modern with storage

Бренд: GARDIVAL Страницы: 10

Бренд: Palmako Страницы: 52

Бренд: Palmako Страницы: 71

Бренд: Palmako Страницы: 55

Бренд: Universo Consumer Products Страницы: 40

Бренд: VERANDA JARDIN Страницы: 24

TEA HOUSE PERGOLA

Бренд: Grange Fencing Страницы: 8

Бренд: Albany Страницы: 2

Бренд: Alfer Страницы: 2

Бренд: Weka Holzbau Страницы: 44

Бренд: Gartenpro Страницы: 35

Бренд: Rowlinson Garden Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды