Duemmegi Contatto MCP 4 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 87

background image

Contatto

MCP 4 – User's manual

DUEMMEGI

10- MCP IDE: INTEGRATED DEVELOPMENT ENVIRONMENT FOR
APPLICATIONS USING MCP 4

10.1- Description of the software package

MCP IDE (Rel 3.2.3 or higher) is an Integrated Development Environment to support the program
development for

Contatto

MCP 4 controller. The MCP IDE package comes complete with an Editor,

Compiler, Transfer utility, Simulator and Supervisor of the operation status of MCP 4 and of the plants.
The package is made by several tool programs, as described here in the following.



MCP IDE

is the MCP 4 program editor, integrating the compiler, the configuration tools for special

modules (e.g. ModTPD transponder reader module, ModHT room controller for hotel applications and so
on) and the “write to / read from” MCP 4 utilities.



MCP VISIO

is a tool allowing the supervision of input and output modules and all other MCP 4

parameters (counters, registers, virtual points, etc.). This tool can work connected to MCP 4 through the
serial port or it can simulate the program written by MCP IDE, in order to debug it before the writing into
MCP 4 FLASH memory.



MCP MAP

is an advanced tool allowing to access to the “heart” of MCP 4; the use of this tool is reserved

to expert user only.



Controtto XT

is an utility for the control of

Contatto

through the PC.

To perform a firmware update of MCP 4 microcontrollers (other than all other

Duemmegi

devices), use the

software package named

BootTools

which can be downloaded from

Duemmegi

site.

The ease of use of MCP IDE and its many features and utilities allow quick development and configuration of
MCP 4 controller, according to the requirements of the plant where it will be installed. The intuitive operation
and the clear menu items allow to start using MCP IDE immediately, allowing to save more time in developing
applications and requiring less time reading user manuals.

10.2- MCP IDE

MCP IDE looks like the following figure:

Page 60 of 87

Rel.: 1.2 October 2018

DUEMMEGI

s.r.l. - Via Longhena, 4 – 20139 MILANO

Tel. 02/57300377 - Fax 02/55213686 –

www.duemmegi.it

«
...
58
59
60
61
62
...
»

Содержание Contatto MCP 4
























































































Отзывы:

Нет отзывов

Похожие инструкции для Contatto MCP 4

Бренд: Galcon Страницы: 32

Бренд: Samson Страницы: 48

Бренд: Magnescale Страницы: 3

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Klimaire Страницы: 5

R1000 series E20

Бренд: Roland Страницы: 156

Бренд: Bandini Industrie Страницы: 42

Бренд: Tate Страницы: 32

Ames Colt Series

Бренд: Watts Страницы: 8

Бренд: CAME Страницы: 40

Бренд: Bucher Hydraulics Страницы: 86

Бренд: KanexPro Страницы: 28

Бренд: Flowserve Страницы: 22

Бренд: Immergas Страницы: 34

Бренд: Azbil Страницы: 100

Бренд: Eaton Страницы: 2

Бренд: Arbor Technology Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды