DT SWISS MTB 2013 SPLINE EX 1501 Скачать руководство пользователя страница 51

Страница: 51 / 76

SPLINE

Technical Manual

rui

5.3

Truing the Wheel

Preparatory Steps

Dismount the wheel.

Dismount the tire and if necessary the tube and the rim tape.

NOTE

Functional impairment / risk of damage due to wrong tools!

Only use the special tools intended for SPLINE

wheels (see

chap.5.2, p.49

Fix the wheel in the truing stand.

Check the radial and axial run out.

NOTE

Risk of damage to the bladed spokes and the nipples!

• Bladed spokes must be hold with the spoke holder while turning the nipple.
• Whenever possible there should be used the universal spoke holder (see

chap.5.2, p.49

) to avoid dama-

ges to the spokes. The spoke holder made out of metal (see

chap.5.2, p.49

) should only be used if the

universal spoke holder can‘t be used due to the high torque.

• There are used different spokes types (see

chap.6.1, p.74

). Ensure that the correct tool is being used.

• To avoid damages to the spoke, slide the spoke holder as far as possible in direction of the rim.
• To avoid damages to the nipples, slide the nipple wrench as far as possible onto the nipple.

Содержание MTB 2013 SPLINE EX 1501













































































Результаты поиска

Содержание MTB 2013 SPLINE EX 1501

Отзывы:

Похожие инструкции для MTB 2013 SPLINE EX 1501

Бренды по названию

Популярные бренды

DT SWISS MTB 2013 SPLINE EX 1501, Техническое руководство

Результаты поиска

Содержание MTB 2013 SPLINE EX 1501

Отзывы:

Похожие инструкции для MTB 2013 SPLINE EX 1501

Бренды по названию

Популярные бренды