8
Programming Access Codes:
Enter [
∗
][5][Master Code] to enter the access code
programming mode. The “Memory”, “Bypass” and “Trouble”
lights will begin to flash. The zone lights are used to indicate
the program status of the 6 access codes.
Zone Light
Zone Light
Zone Light
Zone Light
Zone Light
Access Code Status
Access Code Status
Access Code Status
Access Code Status
Access Code Status
OFF
Code not programmed
steady
Code programmed
Flashing
Code being programmed
Upon entering this programming mode, the 1st zone light
will be ON to indicate that the Master Code is programmed
with the Factory Default Code. The Master Code may be
changed here or in section [21] if the installer chooses to
disable user-changing of the Master Code.
Changing or Adding a Code
To change access codes 1 to 6, press the corresponding key
(1 to 6). The corresponding zone light will begin to flash. Enter
the new four digit number. Do not use the [
∗
] key or [#] key
when entering the four digit number. After the four digits are
entered, the keypad will beep 3 times and the zone light will
come on steady. If you are changing an existing code, the
new code will simply replace the old one. If you wish to
program another code, press the number key for the code to
be programmed and enter the new 4-digit code. Press the
[#] key to exit this section.
Erasing a Code
To erase a code, enter [
∗
][5][Master Code]. Press the key
of the code you wish to erase. The zone light for that code
number will flash. Enter [
∗∗∗∗
].
NOTE:
The Master Code cannot be erased. If the Master
Code is forgotten and the panel is left disarmed, program a
new Master Code using the [
∗
][8][Installer’s Code][21]
command or use the 2nd Master Code to reprogram the
Master Code.
EEPROM Reset
If the Master Code is forgotten and the panel is armed, see
Programming Section [30] for software and hardware methods
of resetting the panel to the factory default condition. Reset
is not necessary if the 2nd Master Code is programmed.
User Function Commands
[
∗∗∗∗∗
]+[6]+[Master Code]
This function is used to set the System Clock time and to set
the Auto-Arm time as well as toggle a number of system
functions. As soon as the command is entered, the “Memory,
“Bypass” and “Trouble ” lights begin to flash.
Enter [
∗
][6][Master Code][Number from list below].
[1]
System 24 Hr. Clock (Enter HH:MM)
[2]
Auto-Arming Time (Enter HH:MM)
[3]
[Reserved for future use]
[4]
Quick-Arm Enable/Disable
[5]
Auto-Arm Enable/Disable
[6]
Door Chime Enable/Disable
[8]
Bell Test Function
[9]
[Reserved for future use]
[0]
Installer’s Test (turn off after use)
(This function will turn off automatically on arming.)
Items [4], [5], [6] and [0] turn ON and OFF various features.
When the item key is pressed and the feature is being turned
ON, the keypad sounder will beep 3 times. If the feature is
being turned OFF the sounder will give one long beep.
Pressing item [8] gives a 2-second Bell / Siren and Keypad
Light and Buzzer test.
Setting the Clock
[
∗∗∗∗∗
]+[6]+[Master Code]+[1]
The System Clock is a 24 Hr. clock and times must be entered
as two digit numbers.
e.g.
HH - 01, 02, .... 10, 11, .... 23, 24
MM - 01, 02, .... 35, 36, .... 58, 59
8:05 AM would be entered as 0805
1:30 PM would be entered as 1330
Setting the system 24 Hr. clock tells the system the time of
day. If the system is without power, (AC and battery), it
cannot continue to keep time. When the panel is powered up,
the system clock must be reset. If the time needs to be reset,
then a trouble #6 will be indicated on the keypad. (See [
∗
][2]
System Trouble Display). Trouble #6 will not be generated if
the Auto-Arm time is not programmed with a valid time. (9999
in these positions disables these features - see Section [19]).
Set Auto-Arm Time
[
∗∗∗∗∗
]+[6]+[Master Code]+[2]
The PC1510 can be programmed to arm at the same time
each day. At the selected Auto-Arm time, the bell will sound
one short burst every 10 seconds for a one minute period if
section [32] light 2 is off. The keypad will also sound for one
minute. If any key is pressed during the 1 minute warning
period, Auto-Arming will be aborted. Auto-Arming will be
attempted at the same time the next day. To set the Auto-Arm
time, enter [
∗
][6][Master Code][2] then enter the hours and
minutes as described at the beginning of this section. This
feature must also be enabled (see item [5] below).
Quick-Arm
ON/ OFF [
∗∗∗∗∗
]+[6]+[Master Code]+[4]
Pressing [4] while in the User Function Command mode will
Enable (3 beeps) or Disable (one long beep) the Quick-Arm
feature. With this feature enabled, the panel can be armed by
simply entering [
∗
][0].
Auto-Arm
ON/OFF [
∗∗∗∗∗
]+[6]+[Master Code]+[5]
Pressing [5] while in the User Function Command mode will
enable (3 beeps) or disable (one long beep) the Auto-Arm
feature. With this feature enabled, the panel will automatically
arm at the same time each day. The time is set in section [19]
or [
∗
][6][Master Code][1].
Door Chime
ON/OFF [
∗∗∗∗∗
]+[6]+[Master Code]+[6]
Pressing [6] while in the User Function Command mode will
enable (3 beeps) or disable (one long beep) the Chime
feature. With this feature enabled, the keypad will beep 5
times when any zone defined as a delay or instant circuit
opens or closes. The Door Chime feature does not operate
on other zone definitions. Zone Bypass may be used to
eliminate beeping on zones where it is not wanted. The Door
Chime feature functions only while the panel is in the
Disarmed mode.