Dresser 5 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 57

background image

9

Also the FIFO communication speed adjustments should be on the lowest settings. This can be reached by
going to Control Panel:Ports:Com Port Settings.

2.4 Verifying the Proper Files Are Loaded

For each Master Meter available for use with the type of ROOTS Model 5 Prover that is currently being used,
read the identification tag attached to the Master Meter(s). Verify that the serial number for each Master Meter
matches the serial number displayed in the initial start up screen of the ROOTS Model 5 Prover software. If one
of the serial numbers does not match the appropriate serial number on the screen, the original factory diskette
(or a copy of it) must be obtained in order to replace the current factory preset file(s). These file names are
P2M.SET, P5M.SET, P10M.SET, P20M.SET and/or P80M.SET and must be copied into the same directory as
the current Prover Software is located, which should be the \\Program Files\Dresser Inc\Model 5 Transfer
Prover\Config Files\subdirectory. The Startup disk should have the same serial number(s) written on the disk
label to match the serial number(s) of the Master Meter(s) on the Prover.

If the installation is a software upgrade and the disk label does not have serial numbers on the disk then the
preset files must be located and put in the same location as the new program files. During the installation
process the location of the new program will be evident. Following is a list of the configuration files that must
be copied to the new location; they are based on the style of Prover that you are using.

Common files for all prover sizes:

• calidate.cfg, calibr.cfg, and MasterMeters. key

and specific files depending on prover size:

•  2M/10M Model 5 Prover: P2M.SET, P10M.SET
•  10M only Model 5 Prover: P10M.SET
•  20M only Model 5 Prover: P20M.SET
•  5M/20M only Model 5 Prover: P5M.SET, P20M.SET
•  10M/80M Model 5 Prover: P10M.SET, P80M.SET
•  80M only Model 5 Prover: P80M.SET

«
...
10
11
12
13
14
...
»

Содержание 5


























































Отзывы:

Нет отзывов

Похожие инструкции для 5

Бренд: Q-See Страницы: 33

AltiWare OE 4.6

Бренд: Altigen Страницы: 518

ANTI-VIRUS FOR WINDOWS SERVERS 9.00

Бренд: F-SECURE Страницы: 48

DVD MOVIEFACTORY 3

Бренд: Ulead Страницы: 78

Бренд: JETWAY Страницы: 43

Бренд: Access Страницы: 16

2521131 - Intel Wasp Motherboard

Бренд: Intel Страницы: 1

H3C IMC STANDARD PLATFORM -

Бренд: 3Com Страницы: 68

AUTOCAD PANDID 2011 - SYSTEM REQUIREMENTS

Бренд: Autodesk Страницы: 2

Бренд: Autodesk Страницы: 6

Бренд: Autodesk Страницы: 62

466B1-05A761-1304 - AutoCAD Inventor Simulation Suite 2010

Бренд: Autodesk Страницы: 84

22906-010000-9325 - UPG FROM AUTOCAD 2000I-NET BUMP

Бренд: Autodesk Страницы: 104

Secure Backup 10.3

Бренд: Oracle Страницы: 174

Trackspacer 2.0

Бренд: Wavefactory Страницы: 10

Бренд: Canon Страницы: 28

Бренд: ADS Technologies Страницы: 12

Samsung Mobile Navigator

Бренд: Garmin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды