Dover Markem Imaje 9040 Скачать руководство пользователя

Страница: 191 / 233

Installation and configuration

A36951-C.doc

192/236

Delete library

Highlight the

NEW

button and then confirm

Highlight the

VALID

button and then confirm

Change library

Highlight the message you want to delete in the library message list, then press

The message is removed from the list.

CAUTION

ALL Following messages are moved up towards the top of
the list.

Go to the general list and highlight the message you want to insert, then press

The message is added to the end of the library list.

Highlight the

VALID

button and then confirm.

The

CANCEL

button is used to exit the function without making any changes.

Using the Ethernet link

The Ethernet link is used to connect the printer to a corporate network.

Establishing the link

Open the console cover to access the Ethernet connector.

Ethernet connector

Foolproofing tab

Содержание Markem Imaje 9040










































































































































































































































Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды

Dover Markem Imaje 9040, Руководство пользователя

Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды