Dover Markem Imaje 9040 Скачать руководство пользователя

Страница: 175 / 233

Alarms and faults

A36951-C.doc

176/236

CPU fault.

6a-

Contact Markem-Imaje Technical Assistance if

the fault persists.

Low ink level.

7a-

Add ink to the tank concerned (max. 1/2 tank).

7b-

The problem may be with the main board.

Contact Markem-Imaje Technical Assistance.

Low additive tank level

or
Additive tank empty
or
Solvent fault.

8a-

Add additive to tank (max. 1/2 tank).

8b-

Check that the additive addition electrovalve is

working correctly (

Production

Maintenance

ELV

status modification

). Check viscometer circuit.

8c-

Contact Markem-Imaje Technical Assistance if

the fault persists.

Fan/compressed air

9a-

Fan failure or no compressed air.

9b-

Check fan connection and ensure that the fan at

the bottom of the cabinet rotates correctly. This fan
should run continuously as soon as the printer is
switched on.

9c-

Ensure pressurization air present (except for

9040 Contrast models).

9d-

The problem is on the main board. Contact

Markem-Imaje Technical Assistance.

10-

Temperature

10a-

The ambient temperature in the room where

the printer is installed is too high and is causing the
temperature inside the electronics compartment to
rise above 70° C. Modify installation.

10b-

The problem is on the main board. Contact

Markem-Imaje Technical Assistance.

11-

Viscosity

11a-

Check viscosity measurement circuit.

11b-

Check viscometer electrovalve operating

correctly by monitoring changes in viscometer
levels (

Production

Maintenance

ELV status

modification

)

11c-

Contact Markem-Imaje Technical Assistance if

the fault persists.

Содержание Markem Imaje 9040










































































































































































































































Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды

Dover Markem Imaje 9040, Руководство пользователя

Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды