Dover Markem Imaje 9040 Скачать руководство пользователя

Страница: 179 / 233

Alarms and faults

A36951-C.doc

180/236

Faults specific to 9040 Contrast printers

CAUTION

The ink circuit includes stirring motors located at the bottom of
the ink and recovery tanks. These are used for mixing the ink
continuously.

The printer must therefore never be disconnected from the
AC supply for more than two hours without draining and
flushing the system beforehand.

Low accumulator level

1a-

The fault occurs after several jet starts or after

refresh sequences, which are excessively long.
Wait for the tank to fill up again.

1b-

Contact Markem-Imaje Technical Assistance if

the fault persists.

Drain recovery tank

2a-

The fault occurs after printhead cleaning or

cleaning solution addition sequences. Drain the
recovery tank via the drain tube provided.

2b-

There is a fault on the recovery tank high-level

detection system. Contact Markem-Imaje Technical
Assistance.

Drain ink tank

3a-

The fault occurs while the printer is being

drained. Drain the tank. Contact Markem-Imaje
Technical Assistance.

Regulator fault

4a-

Activate regulator electrovalve. Press the

key to clear the fault.

4b-

Contact Markem-Imaje Technical Assistance if

the fault persists.

Содержание Markem Imaje 9040










































































































































































































































Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды

Dover Markem Imaje 9040, Руководство пользователя

Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды