Dover Markem Imaje 9040 Скачать руководство пользователя

Страница: 141 / 233

Maintenance

A36951-C.doc

142/236

Open gutter screw.

Select and confirm:

STABILITY

When the jet is stable in the gutter,

select and confirm

JET SHUT DOWN

Clean the print head thoroughly.

Select and confirm

JET START UP

to restart the jet(s)

Make a visual check to ensure jet(s)are in the gutter.

Close the head cover again and press

to clear fault

conditions.

NOTE

In some cases, these three functions can be used individually
or may need to be repeated two or three times.

Before making adjustments

/Status jet(s)/

JET ADJUSTMENT

This function starts up the jet(s) and overrides faults associated with the jet(s). This means
that fault conditions will not prevent you from making adjustments.

Содержание Markem Imaje 9040










































































































































































































































Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды

Dover Markem Imaje 9040, Руководство пользователя

Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды