Dover Markem Imaje 9040 Скачать руководство пользователя

Страница: 138 / 233

Maintenance

A36951-C.doc

139/236

Stopping and starting jets

The default setting is for the jet(s)to be started and stopped automatically.

Jet start-up

(

Production/Status/Printhead/

Status jet(s)

)

Select and confirm

command.

Each head is started separately on a two-headed printer.

The

(and

) indicators go on when the jet(s) are ready (steady

light).

NOTE

The

Production/Printer/

Jet(s) start-up

command allows you

to start all jets (on all heads).

Start mode settings

Production/Printer/

Start mode

This function is used to choose whether all jets are to be started in

Automatic

Manual

mode when the printer started normally.

Содержание Markem Imaje 9040










































































































































































































































Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды

Dover Markem Imaje 9040, Руководство пользователя

Результаты поиска

Содержание Markem Imaje 9040

Отзывы:

Похожие инструкции для Markem Imaje 9040

Бренды по названию

Популярные бренды