Domino G Series Скачать руководство пользователя страница 155

Страница: 155 / 172

PART 5 MAINTENANCE & TROUBLESHOOTING

ERROR DESCRIPTION

Error

Description

Stop print (Normal event)

"Stop" has been selected on the user interface. Printing will

be stopped. No light is on.

Invalid Cartridge

The ink cartridge is not a valid/genuine ink cartridge.

No Cartridge

No ink cartridge is installed.

Ink Low

The ink level in the cartridge is below 5 ml.

Ink Out

The ink level in the cartridge is below 0.4 ml.

Speed Limit

The speed measured by the encoder is too fast. The printer

cannot print at this speed. See,

Printing Speed Table on page

VDC/Real Time Printing

Speed Overload

If real time printing is enabled, after the product detect sensor

is triggered, the label template will immediately be encoded

and sent from the controller to the print head.
If the total time to encode and send the label data to the print

head is longer than the time it takes for the product/print

surface to move from the product detect sensor to the print

head, the label may not print. If this event occurs, printing will

stop and this error will be displayed.
To solution to this error, is to slow down the production line, or

physically move the product detect sensor further away from

the print head.

MAINTENANCE & TROUBLESHOOTING

EPT077343 EN - Issue 1 - 11 November 2022

155

Содержание G Series













































































































































































Результаты поиска

Содержание G Series

Отзывы:

Domino G Series, Руководство по эксплуатации продукта, Страница: 155 / 172

Результаты поиска

Содержание G Series

Отзывы: