Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 350 | Manualshive

Страница: 350 / 440

background image

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.

WARNING!

•

Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
Section 3 of the Warranty Information Book for
additional warranty information.

(Continued)

WARNING! (Continued)

•

The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced technician.

Refrigerant Recovery and Recycling

R-134a Air Conditioning Refrigerant is a hydrofluoro-
carbon (HFC) that is endorsed by the Environmental
Protection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by authorized dealers or other
service facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C system

sealers, stop leak products, seal conditioners, compressor
oil, and refrigerants.

348

MAINTAINING YOUR VEHICLE

«
...
348
349
350
351
352
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

Бренд: Valeo Страницы: 17

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Бренд: Carefree Страницы: 12

Бренд: GOgroove Страницы: 9

Бренд: Subaru Страницы: 3

Бренд: Kia Страницы: 419

Бренд: Ford Страницы: 22

Бренд: CITROËN Страницы: 301

Бренд: XTC Страницы: 4

Бренд: Kuda Страницы: 3

Бренд: Quadratec Страницы: 8

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: Mazda Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды