Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 440

background image

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the
anchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,
grasp and twist the belt webbing 180 degrees to create a
fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.

4. Continue to slide the latch plate up until it clears the
folded webbing.

Seat Belt Pretensioners

The seat belts for both front seating positions are
equipped with pretensioning devices that are designed to
remove any slack from the seat belts in the event of a

collision. These devices improve the performance of the
seat belt system by assuring that the belt is tight around
the occupant in a collision. Pretensioners work for all size
occupants, including those in child restraints.

NOTE:

These devices are not a substitute for proper seat

belt placement by the occupant. The seat belt still must be
worn snug and positioned properly.

The pretensioners are triggered by the Occupant Re-
straint Controller (ORC). (Refer to information on Air-
bags in this section). Like the front airbags, the preten-
sioners are single use items. After a collision that is severe
enough to deploy the airbags and pretensioners, both
must be replaced.

Enhanced Seat Belt Use Reminder System
(BeltAlert

姞

)

If the driver’s seat belt has not been buckled within
60 seconds of starting the vehicle and if the vehicle speed
is greater than 5 mph (8 km/h), the Enhanced Seat Belt

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

41

2

«
...
41
42
43
44
45
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

Porsche 911 Turbo S Wheel

Бренд: FANATEC Страницы: 9

PRIME DESIGN VCR 326

Бренд: Safe Fleet Страницы: 16

Prime Design VBC PC11

Бренд: Safe Fleet Страницы: 8

Prime Design AR1418

Бренд: Safe Fleet Страницы: 4

Бренд: Vaisala Страницы: 24

Lippert Components LEVELEGS MPD 66385

Бренд: Atwood Страницы: 6

65 41 2 152 528

Бренд: BMW Страницы: 21

Бренд: AC Schnitzer Страницы: 16

Бренд: Mercedes-Benz Страницы: 368

Бренд: Fast Master Products Страницы: 13

SANICON TURBO 300

Бренд: Thetford Страницы: 25

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: Westin Страницы: 3

Бренд: Volvo Страницы: 7

Бренд: Connects2 Страницы: 2

Бренд: Metra Electronics Страницы: 12

Бренд: Connects2 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды