Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 342 | Manualshive

Страница: 342 / 440

background image

Trip Odometer button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the MIL.

EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS

In some localities, it may be a legal requirement to pass
an inspection of this vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.

For states that require an Inspection and Mainte-
nance (I/M), this check verifies the Malfunction
Indicator Light (MIL) is functioning and is not on

when the engine is running, and that the OBD II system
is ready for testing.

Normally, the OBD II system will be ready. The OBD II
system may

not

be ready if the vehicle was recently

serviced, recently had a dead battery, or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, the vehicle may fail the test.

This vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if this vehicle’s OBD II system is ready, you must
do the following:

1. Insert the ignition key into the ignition switch.

2. Turn the ignition to the ON position, but do not crank
or start the engine.

3. If you crank or start the engine, you will have to start
this test over.

4. As soon as you turn the ignition key to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.

340

MAINTAINING YOUR VEHICLE

«
...
340
341
342
343
344
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

Бренд: EAL Страницы: 4

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

Бренд: Camcar Страницы: 2

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

Бренд: Dometic Страницы: 158

Бренд: Tachosys Страницы: 28

Бренд: Hyundai Страницы: 11

Бренд: ULTIMATE SPEED Страницы: 40

Бренд: Whispbar Страницы: 14

ASENTO EV-COLC15R

Бренд: ADAPT SOLUTIONS Страницы: 22

2004 JR41 Stratus Sedan

Бренд: Dodge Страницы: 273

Бренд: Airstream Страницы: 103

Automobille 2004 Century

Бренд: Buick Страницы: 12

Directechs FORD11

Бренд: Directed Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды