Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 440

background image

has successfully accepted the frequency signal. The
EVIC display will change from “CHANNEL # TRAIN-
ING” to “CHANNEL # TRAINED.”

If you unplugged the device for training, plug it back in
at this time.

Then proceed with Step 4 under “Programming
HomeLink

威

” earlier in this section.

Using HomeLink

姞

To operate, simply press and release the programmed
HomeLink

威

button. Activation will now occur for the

trained device (i.e., garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.) The hand-held transmitter of the device may also be
used at any time.

Reprogramming A Single HomeLink

姞

Button

To reprogram a channel that has been previously trained,
follow these steps:

1. Turn the ignition switch to the ON/RUN position.

2. Press and hold the desired HomeLink

威

button for

20 seconds until the EVIC display states “CHANNEL #
TRAINING.”

Do not release the button.

3.

Without releasing the button,

proceed with Program-

ming HomeLink

威

Step 2 and follow all remaining steps.

Security

It is advised to erase all channels before you sell or turn
in your vehicle.

To do this, press and hold the two outside buttons for
20 seconds until the EVIC message states “CHANNELS
CLEARED.” Note that all channels will be erased. Indi-
vidual channels cannot be erased.

138

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
138
139
140
141
142
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

KO PROPO RTF 2002 ESC

Бренд: Tamiya Страницы: 2

Бренд: Velleman Страницы: 6

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Green Motion DC 66

Бренд: Eaton Страницы: 18

VIEWLINE 52 MM - MOUNTING 11-09

Бренд: VDO Страницы: 4

Бренд: EUFAB Страницы: 16

Бренд: Streetwize Страницы: 4

Бренд: A-Tach Mounts Страницы: 2

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Бренд: Pontiac Страницы: 20

Бренд: RAM Страницы: 666

PerfectView LCD350

Бренд: Waeco Страницы: 36

Бренд: Porsche Страницы: 127

OUTLANDER PHEV 2022

Бренд: Mitsubishi MOTORS Страницы: 8

DH-RB 05.02 Series

Бренд: Dhollandia Страницы: 65

Бренд: Rosco Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды