Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 332 | Manualshive

Страница: 332 / 440

background image

the instrument cluster) remains on continuously after
starting the engine of the vehicle with the discharged
battery.

8. When removing the jumper cables, reverse the above
sequence exactly. Be careful of the moving belts and fan.

WARNING!

•

You should not try to start your vehicle by pushing
or towing.

•

Do not connect the cable to the negative post of the
discharged battery. The resulting electrical spark
could cause the battery to explode.

(Continued)

WARNING! (Continued)

•

During cold weather when temperatures are be-
low the freezing point, electrolyte in a discharged
battery may freeze. Do not attempt jump-starting
because the battery could rupture or explode. The
battery temperature must be brought above the
freezing point before attempting jump-start.

FREEING A STUCK VEHICLE

If your vehicle becomes stuck in mud, sand, or snow, it
can often be moved by a rocking motion. Turn your
steering wheel right and left to clear the area around the
front wheels. Then shift back and forth between RE-
VERSE and DRIVE. Usually, the least accelerator pedal
pressure to maintain the rocking motion without spin-
ning the wheels is most effective.

330

WHAT TO DO IN EMERGENCIES

«
...
330
331
332
333
334
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Roav Страницы: 10

Бренд: Porsche Страницы: 51

Бренд: Whispbar Страницы: 14

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Бренд: GMC Страницы: 20

Бренд: Mercedes-Benz Страницы: 54

Бренд: Volvo Страницы: 24

Бренд: Softride Страницы: 4

Бренд: Atera Страницы: 3

Бренд: Black Horse Страницы: 5

Бренд: Thule Страницы: 4

Бренд: Axxess Страницы: 16

Бренд: Rigid Hitch Страницы: 2

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

Бренд: Volvo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды