Dodge 2009 Challenger SRT8 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 440

background image

•

Press the brake pedal, or press the clutch pedal to the
floor (manual transmission).

•

Pull the speed control lever toward you (CANCEL).

Pushing and releasing the ON/OFF button or turning the
ignition OFF erases the set speed from memory.

To Resume Speed

If you deactivated the Electronic Speed Control without
erasing the set speed from memory and your vehicle
speed is above 20 mph (32 km/h), you can resume the
previous set speed. To do so, push the lever upward to
RESUME ACCEL and release. Then remove your foot
from the accelerator pedal.

To Vary the Speed Setting

When the Electronic Speed Control is set, you can in-
crease speed by pushing up and holding the lever in
RESUME ACCEL. When the lever is released, a new set
speed will be established.

Tapping the lever to RESUME ACCEL once will result in
a 1 mph (1.6 km/h) speed increase. Each time the lever is
tapped speed increases, so tapping the lever three times
will increase speed by 3 mph (4.8 km/h), etc.

To decrease speed while Electronic Speed Control is set,
push down and hold the lever in SET DECEL. Release the
lever when the desired speed is reached, and a new set
speed will be established.

Tapping the lever to SET DECEL once will result in a
1 mph (1.6 km/h) speed decrease. Each time the lever is
tapped, speed decreases.

To Accelerate For Passing

Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

131

3

«
...
131
132
133
134
135
...
»

Содержание 2009 Challenger SRT8

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 Challenger SRT8

Бренд: UnderCover Страницы: 16

Бренд: 3SIXT Страницы: 12

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Cadillac Страницы: 518

Бренд: Opel Страницы: 141

Бренд: PEUGEOT Страницы: 249

Бренд: Nav TV Страницы: 5

Ram Commercial2016

Бренд: Dodge Страницы: 675

Бренд: U.S. General Страницы: 8

Бренд: STARLANE Страницы: 24

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Бренд: Thule Страницы: 12

Бренд: PUTCO Страницы: 2

Бренд: Joie Страницы: 53

Бренд: Aries Страницы: 3

Бренд: QA1 Страницы: 3

Бренд: Buick Страницы: 371

Бренд: Brodit Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды