DMP Electronics 7133 Скачать руководство пользователя

Страница: 34 / 40

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may

cause undesired operation.

Changes or modifications made by the user and not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Содержание 7133









































Результаты поиска

Содержание 7133

Отзывы:

Похожие инструкции для 7133

Бренды по названию

Популярные бренды

DMP Electronics 7133, Руководство по установке

Результаты поиска

Содержание 7133

Отзывы:

Похожие инструкции для 7133

Бренды по названию

Популярные бренды