DKS 9024-081 Скачать руководство пользователя

Страница: 36 / 44

9024-066-A-1-15

OFF

RESET

ALARM

MANUAL RELEASE

SECTION 6 - OPERATING INSTRUCTIONS

WARNING

To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from gate.

NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE

4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop or reverse when an object

activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust

and retest the gate operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving and power has been shut-off.

6. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate

hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

SAVE THESE INSTRUCTIONS

Unlock the
control panel
cover to access
the controls.

IMPORTANT SAFETY INSTRUCTIONS

ING

TE C

Per

son

s ar

e to

kee

p c

lear

! T

he g

ate

is c

apa

ble

bein

g mo

ved

tho

ut p

rior

arn

ing

t let

ild

ren

era

te th

e g

ate

or p

lay

in th

gate

are

This

trance

is f

or v

icle

s o

nly

. P

ede

stria

st us

e a

sep

ara

te e

ntran

ce.

Per

son

s ar

e to

rea

d th

e o

er’s

anu

al a

safe

ty in

stru

ctio

ns.

For

te o

per

ato

r us

ing

pe D

trap

pro

tec

tion

, an

aut

oma

tic c

los

ing

vice

(su

ch a

s a

tim

er,

loo

p s

ens

or o

r sim

ilar

dev

ice)

all n

ot b

emp

loy

ed.

RIO

CLA

CER

TIF

IED

N/C

2.2

. 24

SI/U

L-325

HICU

LAR

ATOR

533

SERI

LTS

AMP

TE LO

Doo

rKing

, In

c., I

ngl

ood

, C

DC Power Switch

- Powers the DC ON (toggle left) or

OFF (toggle right).

Note:

When powering up operator, the key switch

MUST

be pressed (located on circuit board) AFTER DC

power switch is turned ON to power up operator.

Reset Button

- Push to turn off the entrapment

alarm and to reset the operator after a

HARD

shutdown has occurred.

Alarm Siren

Manual Release

- See page 35.

Push to Operate Button

- Push to cycle the operator.

It will use the auto-close timer when turned ON to
close the gate. Opens gate fully.

PUSH TO OPERATE

technician use only

6.1 Operator Controls and Resets

Содержание 9024-081













































Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды

DKS 9024-081, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды