manualshive.com logo in svg

DKS 9024-081, Инструкция по установке и эксплуатации

Поделиться
Скачать
DKS 9024-081 Скачать руководство пользователя страница 27

9024-066-A-1-15

24

3.2 DIP-Switches Continued

Switch 1 - Operator Opening Direction:

 

Must OPEN

 the operator’s gate upon initial AC power up and 

open command. If the first open command begins to close the gate, turn AC power off and reverse this 
switch. 

Switch 2 - Auto-Close Timer:

 Turns the auto-close timer on or off. If auto-close is ON, maximum time 

that can be set for is approximately 23 secs.
If auto-close is OFF, an open gate will not close until a manual input is received. 

Switch 3 - EXIT Loop Port Output / Full Open Input:

 This switch 

MUST

 be turned 

OFF

 when using solar 

power. 

DO NOT

 turn this switch ON. 

DO NOT

 wire any devices to main terminal 4. 

Switch 4 - Reverse / Stop Gate: 

Determines if an input to main terminal 10 (Photo Sensors) 

AND/OR

 reverse loops will reverse 

OR

 stop a 

CLOSING gate

.

A tailgating vehicle 

can activate

 main terminal 10 (Photo sensors) and/or reverse loops 

while

 the gate is in the closing cycle 

from the previous vehicle’s authorized entry:

If

 switch 4 is turned 

OFF 

(Reverse), the closing gate that gets activated by a tailgating vehicle will reverse back to the open 

position, possibly allowing the tailgating vehicle 

unauthorized entry while the gate is reversing back to the open position

.

If

 switch 4 is turned 

ON 

(Stop), the closing slide gate that gets activated by a tailgating vehicle will stop, partially or completely 

blocking the pathway, 

NOT

 allowing the tailgating vehicle to enter without proper authorization. The slide gate will not move 

until all sensors are clear, usually forcing the tailgating vehicle that activated the sensors to back away from the gate. The slide 
gate will then continue until closed, helping prevent the tailgating vehicle from unauthorized entry.

 

Switch 5 - Quick-Close Timer Override: 

Turning the quick-close feature ON will cause an 

opening gate

 to stop and close when 

the reverse loops and/or photo sensors have been cleared by a vehicle no matter how far the gate has opened (Useful when 
opening a long gate to reduce gate cycling time). This will also override the auto-close timer setting to close the gate after 1 
second, regardless of the time that has been set for the auto-close timer. 

Switches 6-7 - Relay: 

These work in conjunction with each other and determine when the relay on the board (main terminals 

13-14) will be activated. This relay can be used as a switch for various functions such as illuminating a warning light when the 
gate is moving, or turning on a green light when the gate is full open.

Switch 8 - Accessory Power: 

 This switch 

MUST

 be turned 

OFF

 when using solar power. A maximum of 500 mA of constant 

power is supplied to any accessory connected to main terminals 11 and 12. 

DO NOT

 turn this switch ON.

Switches 1-2 - Select Operator Type: 

These switches 

MUST

 be turned 

OFF

 for the Model 9024. They 

indicate the type operator that will be used with the circuit board.

Switch 3 - Input Power Failure Mode:

 This switch 

MUST

 be turned 

OFF

 when using solar power. In the 

event that the solar panel cannot charge the batteries and battery power gets depleted through normal 
gate cycling, gate will fully open and operator will shut down. When solar panel power begins charging 
the batteries again, gate will close. Note: A heavy gate may not completely open during the FINAL 
opening cycle after the battery power has been depleted.

DO NOT

 turn this switch ON.

Switch 4 - Reverse Input:

 This switch 

MUST

 be turned 

OFF

 for the 9024. Main terminal 10 is a reverse input. 

DO NOT

 turn ON.

Switch 5 - Overlapping Dual Gates:

 This switch 

MUST

 be turned 

OFF

 for the 9024. 

DO NOT

 turn ON for the 9024.

Switch 6 - Circuit Board Power Management:

 This switch 

MUST

 be turned 

ON

 when using solar power. It minimizes the power 

drain by the circuit board. When the gate has been closed for 5 min. or held open for 5 min., circuit board will power down to 
conserve power. Main terminals 1, 2, 3 and loop detector ports will remain powered up. An input from one of these connections 
will power up the circuit board again.

DO NOT

 turn ON when using solar power.  

Switches 7-8 - Not Used:

 These switches 

MUST

 be turned 

OFF

 for the Model 9024. 

DO NOT

 turn ON.

SW-1 Switch

(Top 8 switches on circuit board)

SW-2 Switch

(Bottom 8 switches on circuit board)

ON

1
2
345678

SW 1

ON

1
2
345678

SW 2

Typical Settings

Typical Settings

MUST use - OFF
MUST use - OFF
MUST use - OFF
MUST use - OFF
MUST use - OFF

MUST use - ON

MUST use - OFF
MUST use - OFF

Opening - RT/LT

 

Normal - 

ON

MUST use - OFF

Normal - 

OFF

Normal - 

OFF

Normal - 

OFF

Normal - 

OFF

MUST use - OFF

Содержание 9024-081













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды