DKS 9024-081 Скачать руководство пользователя

Страница: 26 / 44

9024-066-A-1-15

3.2 DIP-Switch Settings for 4100 Circuit Board

The two DIP-switches located on the circuit board are used to program the operator to operate in various modes and to turn on
or off various operating features. Whenever a switch setting is changed, reset button must be pressed for the new setting to
take affect. See next page for more information about DIP-switches.

Switch

Function

Setting

Description

SW 1 (Top 8 DIP Switches)

Operator

Opening

Direction

OFF

OFF

6-OFF

6-ON
6-ON

OFF

7-ON

7-OFF

7-ON

Auto-Close

Timer

Accessory Power

Relay:

Main Terminals

13 and 14

6 and 7

Switch

MUST

be turned

OFF

for Solar.

Auto-close timer is

OFF.

Manual input required to close an open gate.

Normal Setting.

Auto-close timer is

. Adjustable from 1-23 seconds.

24 VDC 500 mA

Constant power

for accessories connected to main terminal 12.

DO NOT USE

for Solar.

OFF

Normal Setting.

Quick close feature is

OFF

. Auto-Close timer functions normally.

Quick close feature is

. Opening gate will stop and close as soon as all reversing

inputs (Reverse loops, photo sensors) are cleared regardless of the distance the
gate has opened. Any Auto-Close timer setting overrides to 1 sec.

OFF

Main terminal 10 is a REVERSE input.

DO NOT USE

for the 9024.

Main terminal 10 is a SHADOW loop (Swing gates ONLY)

Normal Setting.

Relay activates when gate is at open limit.

Relay activates when gate is not closed.
Relay activates when gate is opening and open.
Relay activates during opening and closing cycle.

1-OFF

1-OFF

1-ON
1-ON

2-OFF

2-ON

2-OFF

2-ON

Select

Operator

Type

1 and 2

Slide Gate Operator
DO NOT USE

for the 9024.

Swing Gate Operator

DO NOT USE

for the 9024.

Barrier Gate Operator

DO NOT USE

for the 9024.

Overhead Gate Operator

Switch

Function

Setting

Description

SW 2 (Bottom 8 DIP Switches)

Switches 7 and 8

MUST

be turned

OFF

for the 9024.

OFF

Input Power

Failure Mode

Reverse/Shadow

Input

Overlapping

Dual Gates

7 and 8

Gate

operates normally

using ONLY battery back-up power or

Solar input power.

DO NOT USE

for Solar.

Gate

fully opens

shuts down

until

AC power

is restored.

OFF

Circuit Board

Power

Management

Not Used

DO NOT USE

for Solar.

For

115/230 VAC

input power. Board has

Constant power

Used for

Solar

input power. Board

Minimizes power

when not in use. All terminals

shut down power except

main terminals 1, 2, 3

and

loop detector ports

OFF

Switch 5

MUST

be turned

OFF

for the 9024.

DO NOT USE

for the 9024.

Overlapping gates

ARE

used (Dual swing gates ONLY).

Secondary gate starts to open a few seconds before primary gate starts.

Opening direction

using

setting.

Opening direction
using

OFF

setting.

Changes direction operator will cycle open
upon initial AC power up and open command.

Reverses Gate

Stops Gate

(Slide gates)

Quick-Close

Timer Override

(Slide gates)

Not Used

Normal Setting.

Input to main terminal 10 and reverse loop will

reverse

gate

during

close

cycle.

Input to main terminal 10 and/or reverse loop will

stop

gate during

close

cycle –

gate will

continue to close

after input to main terminal 10 and/or reverse loop are

cleared (Helps prevent tailgating).

Setting

MUST

be used

Содержание 9024-081













































Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды

DKS 9024-081, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды