DKS 9024-081 Скачать руководство пользователя

Страница: 20 / 44

9024-066-A-1-15

1.8 Positioning Operator and Chain

1.9 Attaching Operator and Chain

Operator and chain

MUST

be parallel to gate!

DoorKing recommends a
minimum of four (4) 3/8” x 2”
sleeve anchors (not supplied).

Connect Chain Bracket

to Gate.

Weld completely

around bracket. Chain nut
and chain bolt should not
protrude past gate frame.

Use bolts provided in post
mount kit.

Connect chain to chain bolt with
master link. Adjust the chain nuts to
tighten the chain. The chain should sag no
more than one (1) inch per 10 feet of travel.

Do not over tighten the chain.

Operator and
chain are NOT
parallel to gate.

Chain bracket
does NOT
align with
idler wheels.

Chain bracket

MUST

line

up with chain idler wheels!

Chain brackets

MUST

mounted so the chain
remains the same height
as it is on the idler wheels!

Connect Chain to Chain Bracket.

Attaching Operator

to Concrete Pad

Attaching Operator
to Post Mount Plate

Chain

Bracket

Lines up

with Idler

Wheels

Correct

Chain

Bracket

Height

Correct

Chain

Bracket

Height

Chain brackets

positioned

too low.

Chain
Nut

Chain Bolt

Chain Bracket

Option 2

Lock

Washer

Washers

3/8

Chain

brackets

positioned

too high.

Chain

Idler Wheels

YES

Idler Wheel
Top Position
(Front Mount
Installation)

7.75”

Master

Link

Option 1

Gate

Frame

Содержание 9024-081













































Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды

DKS 9024-081, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 9024-081

Отзывы:

Похожие инструкции для 9024-081

Бренды по названию

Популярные бренды