1835-065-J-7-14
34
The user message, followed by the instruction message,
scrolls across the screen from right to left
when the system is not in use. Both the user and instruction message can be programmed to display your
own message. The user message can be a
maximum of 48 characters (spaces count as a character)
and
is entered into the system memory in three blocks. The first two blocks contain 20 characters while the
third block contains 8 characters. The example below shows how the sample message was divided into
three blocks. Use the blank table to organize your own message. Only upper case letters, numbers and
spaces can be programmed from the system keypad.
Factory Default User Message = This Space is For YOUR Scrolling User Programmable Message.
After organizing the user message in the table above, follow the instructions below to enter the message into the system. After
each desired letter, number or space is displayed on the directory, remember to press
*
to enter that character. Spaces count as
a character and must be entered into memory as a character. After a complete block of characters (including spaces) has been
entered, press
*
to enter the block, then start the next block.
Note:
The factory default message was programmed from a PC, therefore upper and lower case letters are displayed.
Example: THANK YOU FOR VISITING OAKWOOD CONDOMINIUMS
Block 1
Block 2
Block 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
T
H
A
N
K
Y
O
U
F
O
R
V
I
S
I
T
I
N
G
O
A
K
W
O
O
D
C
O
N
D
O
M
I
N
I
U
M
S
Block 1
Block 2
Block 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
77
88
99
44
55
66
11
22
33
00
OPER
OPER
WXYZ
WXYZ
TUV
TUV
PQRS
PQRS
MNO
MNO
JKL
JKL
GHI
GHI
DEF
DEF
ABC
ABC
SP
SP
CALL
Z
A
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONS
Use “A to Z” Buttons to Locate
Name and Code Number on Display.
Names are In Alphabetical Order.
To Call, Enter Code Number on
Keypad or Press “Call” Button. If
Line is Busy, Press “#” or “Call” to
Hang Up. Try Again.
Enter on Open Display and Tone.
1.
2.
3.
1.
Press and enter your four-digit MASTER CODE (
beep
).
The LCD display on the 1835 will read: BLOCK 1.
2.
Enter the characters into block 1 (refer to 3.4.1 for reference). Remember to press (
beep
) after each character.
3.
After the last character in block 1 has been entered, press (
beep
) to enter the entire block.
The LCD display will read: BLOCK 2.
4.
Enter the characters into block 2. Remember to press (
beep
) after each character.
5.
After the last character in block 2 has been entered, press (
beep
) to enter the entire block.
The LCD display will read: BLOCK 3.
6.
Enter the characters into block 3. Remember to press (
beep
) after each character.
7.
After the last character in block 3 has been entered, press (
beep
) to enter the entire block.
8.
Press (
beep
) to enter all three blocks into the system memory.
9.
Press together to end this programming sequence (
beeeeeep
).
10.
The new user message will begin to scroll across the screen.
??
??
??
??
00
OPER
OPER
88
TUV
TUV
00
OPER
OPER
3.4.2 Programming the User Message – 1835 System
Содержание 1833 Series
Страница 2: ......
Страница 69: ...1835 065 J 7 14 67...
