1835-065-J-7-14
19
2.2 Terminal Descriptions
Phone Line Connection
16AC
16AC
BAT
1NO
1NC
1C
2RY
2C
A
Z
IMC
5VDC
IMD
SPKR
COM
MIC
PSW
CGND
PHONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Main Terminal
16 V
AC Input Power
16 V
AC Input Power
Back-up Batter
y POSITIVE
For Phone System Only
. (connect negative to terminal 6)
Relay 1 Normally Open – 30 V
o
lt, 3 Amp max.
Relay 1 Normally Closed – 30 V
o
lt, 3 Amp max.
Relay 1 Common – 30 V
o
lt, 3 Amp max.
Relay 2 Contact – 30 V
o
lt, 3 Amp max.
Relay 2 Common – 30 V
o
lt, 3 Amp max.
“A” Button Input.
“Z” Button Input.
14
+12 VDC Power.
13
Common.
12
DATA 1.
11
DATA 0.
10
+12 VDC Power.
9
Common.
8
DATA 1.
7
DATA 0.
6
16 VAC Output.
5
16 VAC Output.
4
Back-up Battery NEGATIVE (For Wiegand Only).
3
Back-up Battery POSITIVE (For Wiegand Only).
2
16.5 VAC Input Power – 20 VA.
1
16.5 VAC Input Power – 20 VA.
(Powers RS-232, elevator control and Wiegand)
1
DATA 1 – Connect to terminal 20 of elevator control board.
2
DATA 0 – Connect to terminal 21 of elevator control board.
3
COMMON – Connect to terminal 22 of elevator control board.
Transmit Data
1
Receive Data
2
Request to Send
3
Clear to Send
4
Signal Ground - Shell
5
Not used
6
(Not used).
5 VDC Power for LED lighting.
(Not used).
Speaker Output.
Common for switch input #4, microphone,
speaker
, AZ & CALL buttons and batter
y neg.
Microphone Input.
Switch Input. A closure between terminals 4 and 6 will cause the designated relay(s) to activate for
the programmed strike time or dial a phone number – see 3.2.7. The Postal Switch is connected here.
Earth Ground Only
(See Section 2.1.3)
.
Phone Line Connection
3
2
1
14
12
13
11
10
9
8
7
6
5
4
3
2
1
Aux Terminal
Removable
RS-232
Terminal
Removable
Elevator Control
Terminal
Non-Removable
Relay 0 Terminal
Non-Removable
Note:
Connect to the Elevator Control Board (2348-010).
See
Elevator Control Board Manual
2348-065 for more info.
100 ft. max. with 1
8
A
WG wire.
200 ft. max. with 16 A
WG wire.
20 V
A
min. for 1
8
33, 1
8
34 and 1
8
35, 40 V
A
min. for 1
8
37.
8
00 ft. max. with 24 A
WG wire.
1600 ft. max. with 22 A
WG wire.
(Wiring
MUST
be twisted and completely isolated from the ground)
See section 4 on page 46 for the locations of the terminals on the circuit board.
Note:
The 14-pin aux terminal can be removed for easy
wiring. Expansion boards are connected here when used.
See
Expansion
Board Manual
2351-065 and
section 2.3.2,
2.3.3 for more
information.
Note:
Located in the upper left corner of circuit
board. The 6-pin terminal can be removed for
easy wiring. Connects a PC (See Section 2.4.2).
Relay 2 Note:
Normally Open and
Normally Closed relay jumper is
used to set
Relay 2
input on the
circuit board (See section 4.7).
NO
NC
C
Normally Open – 30 V
olt, 3 Amp max.
Normally Closed – 30 V
olt, 3 Amp max.
Common – 30 V
olt, 3 Amp max.
1
2
3
4
5
6
NC
NO
26, 30 and 31 Bit
Wiegand input (Card Reader)
activates
Relay 1
for
programmed strike time
26, 30 and 31 Bit
Wiegand input (Card Reader)
activates
Relay 2
for
programmed strike time
For card readers that have additional
lighting for outdoor use.
Содержание 1833 Series
Страница 2: ......
Страница 69: ...1835 065 J 7 14 67...
