Dive Lab XLDS RDC-2 Скачать руководство пользователя страница 58

Страница: 58 / 59

Supplemental Information

This Guide is made available for the express use of owners and users of the Dive Lab XLDS systems.

This information is subject to periodic updates and changes. Always check the Dive Lab web site for the latest versions.

Document XLDS Guide / Table of Contents

Revised September 30, 2019

XLDS O-Ring Chart

3XL25

-012 90D

Plug High Pressure 7/16-20 UNF/ High Pressure Junction Block

3XL29D

-112 90D

Viton / DIN Yoke

4XL62-72

-214 70D

ICS Regulator Tank

4XL62-5

-16

ICS Regulator

4XL62-10

-18

ICS Regulator

4XL62-9

-11

ICS Regulator

4XL62-28

-012

ICS Regulator

4XL62-25

-008

ICS Regulator

4XL62-24

-22

ICS Regulator

4XL62-7

-010

ICS Regulator

4XL62-16

-014 U70

Urathane / ICS Regulator

4XL80

-015 75D

Buna N / EGS Quick Connect

4XL80-2

-015

Backup Ring, Solid / EGS Quick Connect

XLDS PART

O-Ring

Size

XLDS O-Ring Location

1XL15G

-013

1/2-20 Plug / Manifold
1/2-20 Plug / ICS Regulator

1XL15F

-011

3/8-24 Plug / Manifold
Scuba Port Plug

1XL200

-010 V90 VCO Fitting / HP Inlet

1XL42

-110 H70 Pneumo Female QD x 1/4 FNPT / Console

1XL2-5

-111 90D CV3-M8N-1/3-BRASS, Hylok Check Valve 1XL2

XL7A-6

-015 70D Relief Valve

1XL7A-14

-106 90D (Original) Relief Valve

1XL7A-8

-106 70D Relief Valve

6XL9

-112

DIN O-Ring Viton / EGS Tank Valve

6XL12

-015 90D EGS &

Sherwood Tank valve

Содержание XLDS RDC-2




























































Результаты поиска

Содержание XLDS RDC-2

Отзывы:

Похожие инструкции для XLDS RDC-2

Бренды по названию

Популярные бренды

Dive Lab XLDS RDC-2, Руководство по обслуживанию

Результаты поиска

Содержание XLDS RDC-2

Отзывы:

Похожие инструкции для XLDS RDC-2

Бренды по названию

Популярные бренды