Dive Lab XLDS RDC-2 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 59

Dive Lab XLDS RDC-2 Скачать руководство пользователя страница 43

© Copyright 2003-2019 Dive Lab® Inc. All rights reserved.

This Guide is made available for the express use of owners and users of the Dive Lab XLDS systems.

This information is subject to periodic updates and changes. Always check the Dive Lab web site for the latest versions.

Document XLDS Guide – Section Four A

Revised September 30, 2019

39

SECTION FOUR A: RDC REPAIR / MAINTENANCE / OVERHAUL

This lubricant will aid in getting the O- ring (12) in
place.

5.  Install  O-ring  (12)  into  the  recess  area

of  the  top  of  the  piston,  and  work  it  into
the  recess  then  install  the  washer  (13),
and  nut  (14),  then  tighten  the  nut  until  it
bottoms out against the piston.

6.

Slightly

moisten

O-ring

(16),

with

Christo Lube on the new seat (15), then
install the seat into the large opening end of
the regulator body, then press it in using the
3/8” wooden dowel. Figure 69.

Figure 69

7. Pack the piston assembly spring with Silicone

grease. Ensure the grease gets worked in
around the coils, so that the entire spring
area is filled with grease.

Figure 70

Figure 71

8. Insert the piston assembly into the bore of the

piston cap (17), and press the piston assemble
all the way down.

Figure 72

9. Wipe clean any excess grease from the cone

and disc using the lint free cloth.

10. Insert the piston assembly with the piston into

the regulator body, and thread the piston cap

into the body, until it bottoms out then

tighten to 150 inch lbs.

NOTICE

Install  the  new  seat  with  O-ring  into  the  regulator
body  with  the  cone  side  of  the  seat  facing  down,
toward  the  ½”-20  port.  While  it  might  appear  that
the  cone  side  of  the  seat,  and  the  cone  on  the
poppet  shaft  should  go  together,  this  is  not  the
case. The  flat  side  of  the  seat,  is  the side  that seals
against the poppet.

«
...
41
42
43
44
45
...
»

Содержание XLDS RDC-2




























































Отзывы:

Нет отзывов