Ditch Witch C12x Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 123

background image

Service - 86

Cx Series Operator’s Manual

Procedures

Charge

1. Park service vehicle close to disabled

equipment but do not allow vehicles to

touch.

2. Set parking brake in both, if equipped.
3. Turn both off.
4. Disconnect machine controller, if equipped.
5. Inspect battery in disabled machine (B) for

signs of cracking, bulging, leaking, or other

damage.

6. Connect red positive (+) jumper cable clamp

to positive (+) post of battery (2) in disabled

machine.

7. Connect the other red positive (+) jumper

cable clamp to positive (+) post of battery in

service vehicle (A).

8. Connect black negative (-) cable clamp to

negative (-) post of battery in service vehicle.

9. Connect the other black negative (-) cable

clamp to engine or frame ground on disabled machine, at least 12” (305 mm) from failed battery, as

shown.

10. Operate service vehicle engine at 1500-2000 rpm for a few minutes to build an electrical charge in

failed battery.

11. Stop engine in service vehicle.
12. Remove jumper cables from service vehicle, black negative (-) clamp first. Do not allow clamps to

touch.

13. Remove black negative (-) cable clamp from disabled engine or frame ground.
14. Remove red positive (+) cable clamp from disabled machine.
15. Reconnect machine controller, if equipped.
16. Start disabled machine.

IMPORTANT:

Some equipment may

have a positive jumper cable terminal

(1) located externally. If so equipped,

connect red positive (+) jumper cable

clamp to terminal.

«
...
85
86
87
88
89
...
»

Содержание C12x




























































































































Отзывы:

Нет отзывов

Похожие инструкции для C12x

Бренд: Backyard Discovery Страницы: 79

Бренд: Badger Meter Страницы: 16

Бренд: Cadman Страницы: 84

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: Cambro Страницы: 6

Бренд: ParaBody Страницы: 5

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Macht Dental Страницы: 8

Бренд: Magma Страницы: 16

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: Yamaha Страницы: 139

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды