Ditch Witch C12x Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 123

background image

Transport - 50

Cx Series Operator’s Manual

Haul

Load

1. If equipped, put backfill blade in stowed position. See “Backfill Blade” on page 73.
2. Remove parking pin from parking position.
3. Start engine.
4. Set to low throttle.
5. Raise boom clear of trailer, but keep it low.
6. Move machine to rear of trailer and align with ramps.

7. Drive forward slowly to move machine onto trailer until tiedown position is reached.

8. Lower boom to trailer bed, if space allows.
9. Ensure all controls are in neutral position.
10. Shut off machine.
11. Insert parking pin in parking position.
12. Tie down machine.

Horizontal movement. Crushing can cause death or

serious injury. Read and understand operator’s manual and all safety

instructions before use.

Tipover. Crushing can cause injury. When loading/

unloading, run at low throttle. Keep boom low.

IMPORTANT:

Boom should be facing ramps.

NOTICE:

If loading onto tilt-bed trailer, be prepared for trailer to tilt. Load trencher as far to the

front of trailer as possible.

«
...
49
50
51
52
53
...
»

Содержание C12x




























































































































Отзывы:

Нет отзывов

Похожие инструкции для C12x

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Park Central Страницы: 20

Бренд: Qlight Страницы: 4

Бренд: Sable Страницы: 28

Бренд: Makita Страницы: 208

Бренд: Marcy Страницы: 27

Бренд: Rocker Страницы: 23

Бренд: Western Global Страницы: 21

Scanmate-B DGH 8000

Бренд: DGH TECHNOLOGY Страницы: 53

Бренд: Monosem Страницы: 104

Бренд: Stahls Страницы: 2

Бренд: Intellinet Страницы: 2

Бренд: Tormach Страницы: 19

Бренд: ION Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды