Ditch Witch C12x Скачать руководство пользователя страница 81

Страница: 81 / 123

Service - 80

Cx Series Operator’s Manual

Recommended Lubricants

Welding Precaution

Washing Precaution

Recommended Lubricants

Proper lubrication and maintenance protects Ditch Witch® equipment from damage and failure. Service

intervals listed are for minimum requirements. In extreme conditions, service machine more frequently.

Use only genuine Ditch Witch parts, filters, approved lubricants, TJC, and approved coolants to maintain

warranty. Fill to capacities listed in “Specifications” on page 103.

For more information on engine lubrication and maintenance, see your engine manual.

NOTICE:

Welding can damage electronics.

• Welding currents can damage electronic components. Always disconnect the ECU ground

connection from the frame, harness connections to the ECU, and other electronic components

prior to welding on machine or attachments.

• Connect welder ground close to welding point and make sure no electronic components are in the

ground path.

• Failure to disconnect battery will cause damage to battery.

NOTICE:

Water can damage electronics. When cleaning equipment, do not spray electrical

components with water.

Item

Description

GEO

Gasoline engine oil meeting or exceeding API SJ

See oil temperature chart for recommended viscosity grade for each model.

MPL

Multipurpose gear oil meeting API GL-5 (SAE 80W90)

THF

Tractor hydraulic fluid, Phillips 66® PowerTran Fluid, Mobilfluid® 432, Chevron® Tractor

Hydraulic Fluid, Texaco® TDH Oil, or equivalent

Содержание C12x




























































































































Результаты поиска

Содержание C12x

Отзывы:

Похожие инструкции для C12x

Бренды по названию

Популярные бренды

Ditch Witch C12x, Руководство оператора

Результаты поиска

Содержание C12x

Отзывы:

Похожие инструкции для C12x

Бренды по названию

Популярные бренды