Ditch Witch C12x Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 123

background image

Cx Series Operator’s Manual

Drill - 63

Operate

• at least 3’ (1m) behind drill bit
• hook side toward bore
• cradle side toward machine

3. When drill string guide is in correct position, signal machine operator to start bore.
4. Use drill string guide to control the first 5’ (1.5m) of the bore path.
5. When 5’ (1.5m) of rod is in the ground, signal machine operator to stop rotation of drilling

attachment.

6. When drill string has stopped, remove drill string guide and leave area.

Add Rod

If more length is needed, ask a Helper to add a rod section.

Disconnect Drill String from Drilling Attachment

1. Stop rotation of drilling attachment.
2. Operate ground drive controls to move machine in reverse 6” (15cm) to loosen drill string in ground.
3. Disconnect drill string from drilling attachment. Special tool (p/n 351-272) may be used. See

“Disassemble Drill String” on page 68.

4. Move machine in reverse 10’ (3.05m), about the length of a rod section.

Rotating shaft. Crushing will cause death or serious

injury. Stay away.

To help avoid injury:

Only access drilling attachment once rotation has

fully stopped.

«
...
62
63
64
65
66
...
»

Содержание C12x




























































































































Отзывы:

Нет отзывов

Похожие инструкции для C12x

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: AAON Страницы: 36

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: Quadro mdb Страницы: 4

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды