Ditch Witch C12x Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 123

background image

Cx Series Operator’s Manual

Drive - 45

Shut Down

Reduce Track Wear

Rubber tracks are best suited at soil-based jobsites with minimal rocks and debris. To reduce track wear

drive slowly and make wide turns. Avoid the following:

• spinning tracks under heavy load
• turning on sharp objects such as stones, broken concrete, or debris
• quick turns on asphalt or concrete
• driving over curbs or ledges
• driving with track edges pressed against hard walls or curbs
• operating on corrosive materials such as salt or fertilizer

Shut Down

1. When job is complete, move machine to level ground.
2. Stop machine movement.
3. Lower boom, if space allows.
4. Return all controls to neutral.
5. Set to low throttle.
6. Shut off machine.
7. Insert parking pin (1) in parking position (2).

8. Close fuel shutoff valve, if equipped.
9. If leaving machine unattended, remove key, if

equipped.

IMPORTANT:

Stopping position of gear

(3) determines parking position.

«
...
44
45
46
47
48
...
»

Содержание C12x




























































































































Отзывы:

Нет отзывов

Похожие инструкции для C12x

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Farmet Страницы: 102

Бренд: Nitecore Страницы: 4

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: Ultraflex Страницы: 52

Бренд: Palmgren Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды