Ditch Witch C12x Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 123

background image

Drill - 64

Cx Series Operator’s Manual

Operate

Add Rod Section

1. Have Helper connect new rod section to drill string.
2. Slowly move machine forward until new rod section and drilling attachment are about 1” (2.5cm)

apart.

3. Have Helper lightly hold new rod section.
4. Rotate drilling attachment to align slip latches of new rod section and drilling attachment if needed.
5. Move machine forward slowly. As soon as new rod section engages drilling attachment, have Helper

move hands clear.

6. Slightly move forward until slip latch connection is correctly latched.

Pinch point. Crushing will cause serious injury. Stay away.

To help avoid injury:

• Keep hands at least 6” (15cm) from ends of rod.
• Support rods from underneath with open palms. Never grip rods.

«
...
63
64
65
66
67
...
»

Содержание C12x




























































































































Отзывы:

Нет отзывов

Похожие инструкции для C12x

Бренд: GE Страницы: 138

Бренд: Makita Страницы: 10

Бренд: Unitary products group Страницы: 28

Бренд: Jet Страницы: 12

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Vari Lite Страницы: 14

Бренд: Vaniman Страницы: 3

Бренд: XanLite Страницы: 4

SHAKER KEEPER 20V 200

Бренд: Garland Страницы: 84

Turbo Jet 10 i-CON

Бренд: Stocks AG Страницы: 30

Randell DROP-IN 9550-290

Бренд: Unified Brands Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды