Directed Electronics Python 450 ESP Скачать руководство пользователя страница 40

Страница: 40 / 44

shutdown diagnostics

The unit has the ability to report the cause of the last shutdown of the remote start system.

To enter diagnostic mode:

Turn the ignition off.

Press and

HOLD

the Valet/Program switch.

Turn the ignition on and then off.

Release the Valet/Program switch.

Press and release the Valet/Program switch.

The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:

The LED will stop flashing when the ignition is turned on.

LED FLASHES SHUTDOWN MODE

One

System timed out

Two

Over-rev shutdown

Three

Low or no RPM

Four

Transmitter Shutdown (or optional push-button)

Five

(-) Shutdown

Six

(+) Shutdown

Seven

(-) Neutral safety shutdown (H3/6 BLACK/WHITE)

Eight

Wait-to-start timed out

Содержание Python 450 ESP













































Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды

Directed Electronics Python 450 ESP, Руководство по установке

Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды