Directed Electronics Python 450 ESP Скачать руководство пользователя страница 30

Страница: 30 / 44

programming jumpers

This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay is enabled

and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board relay is disabled. The

WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving factory parking light relays.

NOTE:

For parking light circuits that draw 10 amps or more, the internal jumper must be switched

to a (-) light flash output.

P/N 8617

or a standard automotive SPDT relay must be used on the

H1/2 light flash output harness wire.

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their

ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to

the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehi-

cles. The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus,

Stratus, Breeze and LH-based vehicles.

tach threshold on/off

light flash (+)/(-)

Содержание Python 450 ESP













































Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды

Directed Electronics Python 450 ESP, Руководство по установке

Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды