Directed Electronics Python 450 ESP Скачать руководство пользователя страница 42

Страница: 42 / 44

valet mode

To enter or exit Valet® Mode with the Valet®/Program switch:

Turn the ignition on and then off.

Within 10 seconds, press and release the Valet®/Program switch.

The status LED will light solid if you have entered Valet® Mode, and will go out if you have exited Valet® Mode.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The fol-

lowing test procedure must be used to verify proper installation and operation of the system. The installation

must be completed before testing, including connection to the brake switch and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the

engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues

to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start

system. The vehicle should not start. If the starter engages, check your hood pin and connections.

NOTE:

If programmed for Diesel Mode, the system will turn on the ignition, but the starter should

not engage with the hood open.

3. Test the NEUTRAL SAFETY shutdown circuit:

IMPORTANT!

Make sure there is adequate clearance to the front and rear of the vehicle before

attempting this test.

a. Make sure the hood is closed and no other shutdown circuits are active.

b. Set the emergency brake.

c. Turn the ignition key to the run position but do not start the engine.

d. Put the vehicle in Drive (D).

Содержание Python 450 ESP













































Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды

Directed Electronics Python 450 ESP, Руководство по установке

Результаты поиска

Содержание Python 450 ESP

Отзывы:

Похожие инструкции для Python 450 ESP

Бренды по названию

Популярные бренды